EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Filling a Gap in Materials Mechanics: Nanoindentation at High Constant Strain Rates up to 10 5 s −1

Lalith Kumar Bhaskar iD, Dipali Sonawane, Hendrik Holz, Jeongin Paeng, Peter Schweizer, Jing Rao, Bárbara Bellón, Damian Frey, Aloshious Lambai, Laszlo Pethö, Johann Michler, Jakob Schwiedrzik iD und 3 weitere

Small · 2026-05 · 22 (28)

DOI: 10.1002/smll.73215 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small, online erschienen am 01.04.2026. Verfasst von Lalith Kumar Bhaskar und 14 weiteren Autor:innen. Beteiligte Einrichtung: Max-Planck-Institute for Sustainable Materials, Department of Structure and Micro-∖Nano- Mechanics of Materials, Düsseldorf, Germany. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 62 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Research Council (ERC), Eurostars Project HINT, Alexander von Humboldt Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A central focus in high strain rate research is understanding the dynamic behavior of materials at strain rates where a strength upturn is observed. While strength upturns at strain rates of 10 3 to 10 4 s −1 have been widely reported in the literature, their occurrence in certain materials remains controversial, and the underlying physics driving this phenomenon is not yet fully understood. Current mechanical testing methods are limited, as no single technique spans the full strain rate range of 10 1 to 10 5 s −1 where this phenomenon is expected, and a unified technique would enable consistent post‐deformation characterization with minimal error. To address this, we developed a customized piezoelectric in situ nanomechanical test setup, enabling constant indentation strain rates up to 10 5 s −1 , for the first time. Using this system, we examined rate‐dependent hardness in single‐crystalline molybdenum, nanocrystalline nickel, and amorphous fused silica over strain rates from 10 1 to 10 5 s −1 , remarkably revealing a hardness upturn in all three materials. Further, post‐deformation analysis of single‐crystalline molybdenum revealed that the hardness upturn was primarily driven by increased dislocation density, with phonon drag—traditionally considered a dominant contributor playing a minimal role.

Schlagwörter

Stichwörter der Autor:innen

fused silicahardness upturnhigh strain rateinstrumentationmolybdenumnanocrystalline nickelnanoindentation

Autor:innen und Institutionen

  • Max-Planck-Institute for Sustainable Materials, Department of Structure and Micro-∖Nano- Mechanics of Materials, Düsseldorf, Germany.
  • Alemnis AG, Thun, Switzerland.
  • Materials Science and Environmental Engineering, Faculty of Engineering and Natural Sciences, Tampere University, Tampere, Finland.
  • Current address: VTT Technical Research Centre of Finland Ltd., Espoo, Finland.
  • Laboratory of Mechanics of Materials and Nanostructures, Empa - Swiss Federal Laboratories for Materials Science and Technology, Thun, Switzerland.
  • EPFL, École polytechnique fédérale de Lausanne, Institute of Materials (IMX), Lausanne, Switzerland.

ORCID-Profile: Lalith Kumar Bhaskar, Jakob Schwiedrzik

Förderung

  • European Research Council (ERC)
  • Eurostars Project HINT
  • Alexander von Humboldt Foundation
  • Alexander von Humboldt-Stiftung

Zitieren

APA

Bhaskar, L. K., Sonawane, D., Holz, H., Paeng, J., Schweizer, P., Rao, J., Bellón, B., Frey, D., Lambai, A., Pethö, L., Michler, J., Schwiedrzik, J., Mohanty, G., Dehm, G., & Ramachandramoorthy, R. (2026). Filling a Gap in Materials Mechanics: Nanoindentation at High Constant Strain Rates up to 10 5 s −1. Small, 22(28). https://doi.org/10.1002/smll.73215

Vancouver

Bhaskar LK, Sonawane D, Holz H, Paeng J, Schweizer P, Rao J, et al. Filling a Gap in Materials Mechanics: Nanoindentation at High Constant Strain Rates up to 10 5 s −1. Small. 2026;22(28). doi:10.1002/smll.73215

BibTeX
@article{Bhaskar2026,
  author = {Bhaskar, Lalith Kumar and Sonawane, Dipali and Holz, Hendrik and Paeng, Jeongin and Schweizer, Peter and Rao, Jing and Bellón, Bárbara and Frey, Damian and Lambai, Aloshious and Pethö, Laszlo and Michler, Johann and Schwiedrzik, Jakob and Mohanty, Gaurav and Dehm, Gerhard and Ramachandramoorthy, Rajaprakash},
  title = {Filling a Gap in Materials Mechanics: Nanoindentation at High Constant Strain Rates up to 10 5 s −1},
  journal = {Small},
  year = {2026},
  volume = {22},
  number = {28},
  doi = {10.1002/smll.73215}
}
Kostenlos starten →