EUVIMEDEUVIMED entdecken
Crossref

Formation Characteristics of Pt‐Ni Alloy Nanoparticles Fabricated by Nanolamination of Atomic Layer Deposition in Hydrogen

Ming-Wei Liao iD, Tzu-Kang Chin, Xu-Feng Luo, Yu-Chun Chuang, Tsong-Pyng Perng iD

Small · 2024-11 · 20 (48)

DOI: 10.1002/smll.202404943 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Small, online erschienen am 09.09.2024. Verfasst von Ming-Wei Liao und 4 weiteren Autor:innen. Beteiligte Einrichtung: Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu, 300, Taiwan. Die Arbeit wurde bisher 13-mal zitiert (Crossref) und nennt 46 Literaturangaben. Gefördert von: Ministry of Science and Technology, Taiwan, National Science and Technology Council.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Forced‐flow atomic layer deposition nanolamination is employed to fabricate Pt‐Ni nanoparticles on XC‐72, with the compositions ranging from Pt 94 Ni 6 to Pt 67 Ni 33 . Hydrogen is used as a co‐reactant for depositing Pt and Ni. The growth rate of Pt is slower than that using oxygen reactant, and the growth exhibits preferred orientation along the (111) plane. Ni shows much slower growth rate than Pt, and it is only selectively deposited on Pt, not on the substrate. Higher ratios of Ni would hinder subsequent stacking of Pt atoms, resulting in lower overall growth rate and smaller particles (1.3–2.1 nm). Alloying of Pt with Ni causes shifted lattice that leads to larger lattice parameter and d‐spacing as Ni fraction increases. From the electronic state analysis, Pt 4f peaks are shifted to lower binding energies with increasing the Ni content, suggesting charge transfer from Ni to Pt. Schematic of the growth behavior is proposed. Most of the alloy nanoparticles exhibit higher electrochemical surface area and oxygen reduction reaction activity than those of commercial Pt. Especially, Pt 83 Ni 17 and Pt 87 Ni 13 show excellent mass activities of 0.76 and 0.59 A mg Pt −1 , respectively, higher than the DOE target of 2025, 0.44 A mg Pt −1 .

Schlagwörter

Stichwörter der Autor:innen

Pt‐Ni alloy nanoparticlesatomic layer depositionnanolaminationoxygen reduction reactionproton exchange membrane fuel cell

Autor:innen und Institutionen

  • Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu, 300, Taiwan.
  • National Synchrotron Radiation Research Center, Hsinchu, 300, Taiwan.

ORCID-Profile: Ming-Wei Liao, Tsong-Pyng Perng

Förderung

  • Ministry of Science and Technology, Taiwan
  • National Science and Technology Council

Zitieren

APA

Liao, M. W., Chin, T. K., Luo, X. F., Chuang, Y. C., & Perng, T. P. (2024). Formation Characteristics of Pt‐Ni Alloy Nanoparticles Fabricated by Nanolamination of Atomic Layer Deposition in Hydrogen. Small, 20(48). https://doi.org/10.1002/smll.202404943

Vancouver

Liao MW, Chin TK, Luo XF, Chuang YC, Perng TP. Formation Characteristics of Pt‐Ni Alloy Nanoparticles Fabricated by Nanolamination of Atomic Layer Deposition in Hydrogen. Small. 2024;20(48). doi:10.1002/smll.202404943

BibTeX
@article{Liao2024,
  author = {Liao, Ming-Wei and Chin, Tzu-Kang and Luo, Xu-Feng and Chuang, Yu-Chun and Perng, Tsong-Pyng},
  title = {Formation Characteristics of Pt‐Ni Alloy Nanoparticles Fabricated by Nanolamination of Atomic Layer Deposition in Hydrogen},
  journal = {Small},
  year = {2024},
  volume = {20},
  number = {48},
  doi = {10.1002/smll.202404943}
}
Kostenlos starten →