Direct‐Patterning ZnO Deposition by Atomic‐Layer Additive Manufacturing Using a Safe and Economical Precursor
Small · 2023-09 · 19 (36)
DOI: 10.1002/smll.202301774 ↗Kurz gefasst
Fachartikel in der Zeitschrift Small, 2023-05. Verfasst von Sonja Stefanovic und 8 weiteren Autor:innen. Beteiligte Einrichtung: Friedrich-Alexander-Universität Erlangen-Nürnberg, Chemistry of Thin Film Materials, IZNF, Cauerstraße 3, 91058, Erlangen, Germany. Die Arbeit wurde bisher 23-mal zitiert (Crossref) und nennt 20 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Research Council, Deutsche Forschungsgemeinschaft, China Scholarship Council.
Abstract (Originalsprache)
Area‐selective atomic layer deposition (AS‐ALD) is a bottom‐up nanofabrication method delivering single atoms from a molecular precursor. AS‐ALD enables self‐aligned fabrication and outperforms lithography in terms of cost, resistance, and equipment prerequisites, but it requires pre‐patterned substrates and is limited by insufficient selectivity and finite choice of substrates. These challenges are circumvented by direct patterning with atomic‐layer additive manufacturing (ALAM) — a transfer of 3D‐printing principles to atomic‐layer manufacturing where a precursor supply nozzle enables direct patterning instead of blanket coating. The reduced precursor vapor consumption in ALAM as compared with ALD calls for the use of less volatile precursors by replacing diethylzinc used traditionally in ALD with bis(dimethylaminopropyl)zinc, Zn(DMP) 2 . The behavior of this novel ZnO ALAM process follows that of the corresponding ALD in terms of deposit quality and growth characteristics. The temperature window for self‐limiting growth of stoichiometric, crystalline material is 200–250 °C. The growth rates are 0.9 Å per cycle in ALD (determined by spectroscopic ellipsometry) and 1.1 Å per pass in ALAM (imaging ellipsometry). The preferential crystal orientation increases with temperature, while energy‐dispersive X‐ray spectroscopic and XPS show that only intermediate temperatures deliver stoichiometric ZnO. A functional thin‐film transistor is created from an ALAM‐deposited ZnO line and characterized.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Friedrich-Alexander-Universität Erlangen-Nürnberg, Chemistry of Thin Film Materials, IZNF, Cauerstraße 3, 91058, Erlangen, Germany.
- Inorganic Materials Chemistry, Ruhr-Universität Bochum, Universitätsstraße 150, 44801, Bochum, Germany.
- ATLANT 3D Nanosystems ApS Mårkaervej 2, DK-2630 Taastrup, Mårkaervej 2, Taastrup, DK-2630, Denmark.
- Friedrich-Alexander-Universität Erlangen-Nürnberg, Organic Materials and Devices, IZNF, Cauerstraße 3, 91058, Erlangen, Germany.
ORCID-Profile: David Zanders, Marcus Halik, Anjana Devi, Julien Bachmann
Förderung
- European Research Council
- Deutsche Forschungsgemeinschaft
- China Scholarship Council
Zitieren
APA
Stefanovic, S., Gheshlaghi, N., Zanders, D., Kundrata, I., Zhao, B., Barr, M. K. S., Halik, M., Devi, A., & Bachmann, J. (2023). Direct‐Patterning ZnO Deposition by Atomic‐Layer Additive Manufacturing Using a Safe and Economical Precursor. Small, 19(36). https://doi.org/10.1002/smll.202301774
Vancouver
Stefanovic S, Gheshlaghi N, Zanders D, Kundrata I, Zhao B, Barr MKS, et al. Direct‐Patterning ZnO Deposition by Atomic‐Layer Additive Manufacturing Using a Safe and Economical Precursor. Small. 2023;19(36). doi:10.1002/smll.202301774
BibTeX
@article{Stefanovic2023,
author = {Stefanovic, Sonja and Gheshlaghi, Negar and Zanders, David and Kundrata, Ivan and Zhao, Baolin and Barr, Maïssa K S and Halik, Marcus and Devi, Anjana and Bachmann, Julien},
title = {Direct‐Patterning ZnO Deposition by Atomic‐Layer Additive Manufacturing Using a Safe and Economical Precursor},
journal = {Small},
year = {2023},
volume = {19},
number = {36},
doi = {10.1002/smll.202301774}
}
EUVIMED