EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

3D printer platform and conductance feedback loop for automated imaging of uneven surfaces by liquid microjunction‐surface sampling probe mass spectrometry

Matthias Hermann iD, Haidy Metwally, Jian Yu, Rachael Smith, Hailey Tomm, Martin Kaufmann, Kevin Y M Ren, Chang Liu, Yves LeBlanc, Thomas R Covey iD, Avena C Ross, Richard D Oleschuk iD

Rapid Communications in Mass Spectrometry · 2025

DOI: 10.1002/rcm.9492 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Rapid Communications in Mass Spectrometry, 2025. Verfasst von Matthias Hermann und 11 weiteren Autor:innen. Beteiligte Einrichtung: Department of Chemistry, Queen's University, Kingston, Ontario, Canada. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Molecular Imaging, Mass Spectrometry. Die Arbeit wurde bisher 10-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Natural Sciences and Engineering Research Council of Canada.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Rationale

Molecular imaging of samples using mass spectrometric techniques, such as matrix‐assisted laser desorption ionization or desorption electrospray ionization, requires the sample surface to be even/flat and sliced into thin sections ( c . 10 μm). Furthermore, sample preparation steps can alter the analyte composition of the sample. The liquid microjunction‐surface sampling probe (LMJ‐SSP) is a robust sampling interface that enables surface profiling with minimal sample preparation. In conjunction with a conductance feedback system, the LMJ‐SSP can be used to automatically sample uneven specimens.

Methods

A sampling stage was built with a modified 3D printer where the LMJ‐SSP is attached to the printing head. This setup can scan across flat and even surfaces in a predefined pattern (“static sampling mode”). Uneven samples are automatically probed in “conductance sampling mode” where an electric potential is applied and measured at the probe. When the probe contacts the electrically grounded sample, the potential at the probe drops, which is used as a feedback signal to determine the optimal position of the probe for sampling each location.

Results

The applicability of the probe/sensing system was demonstrated by first examining the strawberry tissue using the “static sampling mode.” Second, porcine tissue samples were profiled using the “conductance sampling mode.” With minimal sample preparation, an area of 11 × 15 mm was profiled in less than 2 h. From the obtained results, adipose areas could be distinguished from non‐adipose parts. The versatility of the approach was further demonstrated by directly sampling the bacteria colonies on agar and resected human kidney (intratumoral hemorrhage) specimens with thicknesses ranging from 1 to 4 mm.

Conclusion

The LMJ‐SSP in conjunction with a conductive feedback system is a powerful tool that allows for fast, reproducible, and automated assessment of uneven surfaces with minimal sample preparation. This setup could be used for perioperative assessment of tissue samples, food screening, and natural product discovery, among others.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalMolecular ImagingMass SpectrometryAnimalsSwineEquipment DesignSurface PropertiesKidney

Autor:innen und Institutionen

  • Department of Chemistry, Queen's University, Kingston, Ontario, Canada.
  • Department of Surgery, Queen's University, Kingston, Ontario, Canada.
  • Department of Pathology, Queen's University, Kingston, Ontario, Canada.
  • SCIEX, Concord, Ontario, Canada.

ORCID-Profile: Matthias Hermann, Thomas R Covey, Richard D Oleschuk

Förderung

  • Natural Sciences and Engineering Research Council of Canada

Zitieren

APA

Hermann, M., Metwally, H., Yu, J., Smith, R., Tomm, H., Kaufmann, M., Ren, K. Y. M., Liu, C., LeBlanc, Y., Covey, T. R., Ross, A. C., & Oleschuk, R. D. (2025). 3D printer platform and conductance feedback loop for automated imaging of uneven surfaces by liquid microjunction‐surface sampling probe mass spectrometry. Rapid Communications in Mass Spectrometry. https://doi.org/10.1002/rcm.9492

Vancouver

Hermann M, Metwally H, Yu J, Smith R, Tomm H, Kaufmann M, et al. 3D printer platform and conductance feedback loop for automated imaging of uneven surfaces by liquid microjunction‐surface sampling probe mass spectrometry. Rapid Communications in Mass Spectrometry. 2025. doi:10.1002/rcm.9492

BibTeX
@article{Hermann2025,
  author = {Hermann, Matthias and Metwally, Haidy and Yu, Jian and Smith, Rachael and Tomm, Hailey and Kaufmann, Martin and Ren, Kevin Y M and Liu, Chang and LeBlanc, Yves and Covey, Thomas R and Ross, Avena C and Oleschuk, Richard D},
  title = {3D printer platform and conductance feedback loop for automated imaging of uneven surfaces by liquid microjunction‐surface sampling probe mass spectrometry},
  journal = {Rapid Communications in Mass Spectrometry},
  year = {2025},
  doi = {10.1002/rcm.9492}
}
Kostenlos starten →