EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Self‐standing gelatin‐ methacryloyl 3D structure using Carbopol ‐embedded printing

Simona Villata, Francesca Frascella, Cesare Gabriele Gaglio, Giuliana Nastasi, Mauro Petretta, Candido Fabrizio Pirri, Désirée Baruffaldi

Journal of Polymer Science · 2024-06 · 62 (11) · 2259-2269

DOI: 10.1002/pol.20240037 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Polymer Science, online erschienen am 19.03.2024. Verfasst von Simona Villata und 6 weiteren Autor:innen. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 37 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Gelatin‐methacryloyl (GelMA) hydrogel has gained huge success in the last decades thanks to its versatilities in many applications. Notably, one of them is 3D bioprinting, as GelMA physical‐mechanical properties and biocompatibility of uncured formulation perfectly suit the requirements of a bioink. Nevertheless, before the photopolymerization, the hydrogel shows weak mechanical properties and long recovery time after stress application, which results in the inability to obtain complex and self‐standing forms due to structure collapse. In this work, Carbopol ETD 2020 NF, dissolved in cell culture medium, was used as supporting bath to optimize GelMA bioprinting and overcome its stability limitations. The achieved results demonstrated the possibility of printing shapes containing hollows with lumens or non‐planar surfaces, also by using nozzles with larger inner diameter, which reduced cell death during printing process, but were usually avoid because of low resolution. Moreover, constructs' extraction was easier when Carbopol solution was prepared in culture medium rather than in water, reducing sample handling. In conclusion, thanks to this supporting bath, it was possible to print cellularized scaffold, with channels that were then seeded, obtaining inner structure. Further, this Carbopol formulation could be considered an eligible candidate as a supporting bath to obtain GelMA 3D self‐standing‐shaped and vascularized scaffold.

Zitieren

APA

Villata, S., Frascella, F., Gaglio, C. G., Nastasi, G., Petretta, M., Pirri, C. F., & Baruffaldi, D. (2024). Self‐standing gelatin‐ methacryloyl 3D structure using Carbopol ‐embedded printing. Journal of Polymer Science, 62(11), 2259-2269. https://doi.org/10.1002/pol.20240037

Vancouver

Villata S, Frascella F, Gaglio CG, Nastasi G, Petretta M, Pirri CF, et al. Self‐standing gelatin‐ methacryloyl 3D structure using Carbopol ‐embedded printing. Journal of Polymer Science. 2024;62(11):2259-2269. doi:10.1002/pol.20240037

BibTeX
@article{Villata2024,
  author = {Villata, Simona and Frascella, Francesca and Gaglio, Cesare Gabriele and Nastasi, Giuliana and Petretta, Mauro and Pirri, Candido Fabrizio and Baruffaldi, Désirée},
  title = {Self‐standing gelatin‐ methacryloyl 3D structure using Carbopol ‐embedded printing},
  journal = {Journal of Polymer Science},
  year = {2024},
  volume = {62},
  number = {11},
  pages = {2259--2269},
  doi = {10.1002/pol.20240037}
}
Kostenlos starten →