EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Toward High‐Performance Piezoresistive Polymer Derived SiOC Ceramics through Masked Stereolithography 3D Printing with β‐Silicon Carbide Nanopowder Reinforcement

Md Sazzadur Rahman iD, Arindam Phani, Seonghwan Kim iD

Macromolecular Rapid Communications · 2024-03 · 45 (5)

DOI: 10.1002/marc.202300602 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Macromolecular Rapid Communications, online erschienen am 12.12.2023. Verfasst von Md Sazzadur Rahman und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical and Manufacturing Engineering, Schulich School of Engineering, University of Calgary, Calgary, AB, T2N 1N4, Canada. Hauptthemen laut MEDLINE: Stereolithography, Printing, Three-Dimensional, Carbon Compounds, Inorganic, Silicon Compounds. Die Arbeit wurde bisher 11-mal zitiert (Crossref) und nennt 70 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: Natural Sciences and Engineering Research Council of Canada, Canada Research Chairs.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Enhancing the piezoresistivity of polymer‐derived silicon oxycarbide ceramics (SiOC PDC ) is of great interest in the advancement of highly sensitive pressure/load sensor technology for use in harsh and extreme working conditions. However, a facile, low cost, and scalable approach to fabricate highly piezoresistive SiOC PDC below 1400 °C still remains a great challenge. Here, the fabrication and enhancement of piezoresistive properties of SiOC PDC reinforced with β‐SiC nanopowders (SiC NP ) through masked stereolithography‐based 3D‐printing and subsequent pyrolysis at 1100 °C are demonstrated. The presence of free carbon in SiC NP augments high piezoresistivity in the fabricated SiC NP ‐SiOC PDC composites even at lower pyrolysis temperatures. A gauge factor (GF) in the range of 4385–5630 and 6129–8987 with 0.25 and 0.50 wt% of SiC NP , respectively is demonstrated, for an applied pressure range of 0.5–5 MPa at ambient working conditions. The reported GF is significantly higher compared to those of any existing SiOC PDC materials. This rapid and facile fabrication route with significantly enhanced piezoresistive properties makes the 3D‐printed SiC NP ‐SiOC PDC composite a promising high‐performance material for the detection of pressure/load in demanding applications. Also, the overall robustness in mechanical properties and load‐bearing capability ensures its long‐term stability and makes it suitable for challenging and severe environment applications.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

StereolithographyPrinting, Three-DimensionalCarbon Compounds, InorganicSilicon CompoundsCeramicsPolymers

Stichwörter der Autor:innen

3D printingpiezoresistivepolymer-derived ceramicstereolithographyβ-SiC nanopowder

Substanzen

silicon carbidePolymersCarbon Compounds, InorganicSilicon Compounds

Autor:innen und Institutionen

  • Department of Mechanical and Manufacturing Engineering, Schulich School of Engineering, University of Calgary, Calgary, AB, T2N 1N4, Canada.

ORCID-Profile: Md Sazzadur Rahman, Seonghwan Kim

Förderung

  • Natural Sciences and Engineering Research Council of Canada
  • Canada Research Chairs

Zitieren

APA

Rahman, M. S., Phani, A., & Kim, S. (2024). Toward High‐Performance Piezoresistive Polymer Derived SiOC Ceramics through Masked Stereolithography 3D Printing with β‐Silicon Carbide Nanopowder Reinforcement. Macromolecular Rapid Communications, 45(5). https://doi.org/10.1002/marc.202300602

Vancouver

Rahman MS, Phani A, Kim S. Toward High‐Performance Piezoresistive Polymer Derived SiOC Ceramics through Masked Stereolithography 3D Printing with β‐Silicon Carbide Nanopowder Reinforcement. Macromolecular Rapid Communications. 2024;45(5). doi:10.1002/marc.202300602

BibTeX
@article{Rahman2024,
  author = {Rahman, Md Sazzadur and Phani, Arindam and Kim, Seonghwan},
  title = {Toward High‐Performance Piezoresistive Polymer Derived SiOC Ceramics through Masked Stereolithography 3D Printing with β‐Silicon Carbide Nanopowder Reinforcement},
  journal = {Macromolecular Rapid Communications},
  year = {2024},
  volume = {45},
  number = {5},
  doi = {10.1002/marc.202300602}
}
Kostenlos starten →