EUVIMEDOpdag EUVIMED
Crossref

Effect of 3D printing conditions and post‐printing fermentation on pearl millet fortified idli

Vijayakumar Raja, Jeyan Arthur Moses iD, Chinnaswamy Anandharamakrishnan iD

Journal of the Science of Food and Agriculture · 2023-03-30 · 103 (5) · 2401-2412

DOI: 10.1002/jsfa.12410 ↗

At a glance

Journal article in Journal of the Science of Food and Agriculture, published online on 2023-01-15. Written by Vijayakumar Raja and 2 co-authors. Institution: Computational Modeling and Nanoscale Processing Unit, National Institute of Food Technology, Entrepreneurship and Management-Thanjavur (NIFTEM-T), Mi…. Major MEDLINE topics: Pennisetum. Cited 31 times so far (Crossref); 52 references. Funded by: Ministry of Food Processing Industries.

AbstractSubjectsBibliografiske oplysningerCiteRelated studies

Abstract (original language)

BACKGROUND Three‐dimensional (3D) printing is an emerging technology with numerous applications in the development of novel foods to meet personalized and special dietary needs. Using 3D printing, foods with modified textures and consistency can be prepared conveniently. In this work, an indigenous rice–black gram batter was fortified with pearl millet flour and 3D printed in the in‐house developed extrusion‐based food printer, Controlled Additive‐manufacturing Robotic Kit (CARK™). The impact of material supply composition was investigated along with optimization of different printing parameters and an in‐depth analysis of post‐printing fermentation kinetics was undertaken. The shape changes in the 3D printed constructs during fermentation were analyzed using a pixel‐count‐based image‐processing technique that correlates with the change in surface area. RESULTS The addition of millet flour resulted in accelerated fermentation. At 20% w/w level, better printability with higher precision and layer definition was obtained at 800 mm min −1 of printing speed, 360 rpm extrusion motor speed, and 1.22 mm nozzle diameter with an extrusion rate of 15.57 mm 3 s −1 . The constructs of pearl millet flour (PMF) fortified idli batter have shown good structural stability and creep recovery. Fermentation‐assisted shape change was found to be significantly influenced by infill levels. Both raw and steamed constructs with 40% infill showed around 37% lower hardness than 100% infill constructs due to a porous inner structure with reduced expansion in the surface area/volume during fermentation. CONCLUSION The results of the study provide insights into the scope of printing fermented foods through the food‐to‐food fortification approach and textural modification of foods using 3D printing by varying the infill levels. © 2022 Society of Chemical Industry.

Subjects

MeSH terms (MEDLINE)

PennisetumFood HandlingFermentationFlourPrinting, Three-Dimensional

Author keywords

3D printingfermentation kineticsidli batterinfill levelpearl millet

Authors and institutions

  • Computational Modeling and Nanoscale Processing Unit, National Institute of Food Technology, Entrepreneurship and Management-Thanjavur (NIFTEM-T), Ministry of Food Processing Industries, Government of India, Thanjavur,…

ORCID profiles: Jeyan Arthur Moses, Chinnaswamy Anandharamakrishnan

Funding

  • Ministry of Food Processing Industries

Cite

APA

Raja, V., Moses, J. A., & Anandharamakrishnan, C. (2023). Effect of 3D printing conditions and post‐printing fermentation on pearl millet fortified idli. Journal of the Science of Food and Agriculture, 103(5), 2401-2412. https://doi.org/10.1002/jsfa.12410

Vancouver

Raja V, Moses JA, Anandharamakrishnan C. Effect of 3D printing conditions and post‐printing fermentation on pearl millet fortified idli. Journal of the Science of Food and Agriculture. 2023;103(5):2401-2412. doi:10.1002/jsfa.12410

BibTeX
@article{Raja2023,
  author = {Raja, Vijayakumar and Moses, Jeyan Arthur and Anandharamakrishnan, Chinnaswamy},
  title = {Effect of 3D printing conditions and post‐printing fermentation on pearl millet fortified idli},
  journal = {Journal of the Science of Food and Agriculture},
  year = {2023},
  volume = {103},
  number = {5},
  pages = {2401--2412},
  doi = {10.1002/jsfa.12410}
}
Start for free →