EUVIMEDEUVIMED entdecken
Crossref

Synthesis of biocompatible Ti ‐ 6Al ‐ 4V composite reinforced with ZrO 2 and bioceramic produced by powder metallurgy: Morphological, structural, and biocompatibility analysis

Muharrem Pul iD, Ümit Erdem iD, Büşra Moran Bozer, Tuncay Şimşek, Rüstem Yılmazel, Mustafa Yasin Erten

Microscopy Research and Technique · 2024

DOI: 10.1002/jemt.24646 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Microscopy Research and Technique, 2024. Verfasst von Muharrem Pul und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Electricity and Energy, Kırıkkale University, Kırıkkale Vocational School, Kırıkkale, Turkey. Hauptthemen laut MEDLINE: Zirconium, Alloys, Biocompatible Materials, Titanium. Die Arbeit wurde bisher 4-mal zitiert (Crossref) und nennt 76 Literaturangaben. Gefördert von: Kırıkkale University Scientific Research Projects Unit.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this experimental study, the initial phase involved preparing composite structures with various mix ratios using the Ti‐6Al‐4V alloy, widely used in clinical applications, in conjunction with ZrO 2 and hydroxyapatite (HA) synthesized via the precipitation method, employing powder metallurgy techniques. Subsequently, the microstructures of the resultant hybrid composite materials were imaged, and x‐ray diffraction (XRD) phase analyses were conducted. In the final phase of the experimental work, tests were performed to determine the biocompatibility properties of the hybrid composites. For this purpose, cytotoxicity and genotoxicity assays were carried out. The tests and examinations revealed that structures compatible both morphologically and elementally were obtained with no phase transformations that could disrupt the structure. The incorporation of ZrO 2 into the Ti‐6Al‐4V alloy was observed to enhance cell viability values. The value of 98.25 ± 0.42 obtained by adding 20% ZrO 2 gave the highest cell viability result. The addition of HA into the hybrid structures further increased the cell viability values by approximately 10%. All viability values for both HA‐added and HA‐free groups were obtained above the 70% viability level defined in the standard. According to the genotoxicity test results, the highest cytokinesis‐block proliferation index values were obtained as 1.666 and 0.620 in structures containing 20% ZrO 2 and 10% ZrO 2 + 10% HA, respectively. Remarkably, all fabricated composite and hybrid composite materials surpassed established biocompatibility standards and exhibited nontoxic and nongenotoxic properties. This comprehensive study contributes vital insights for future biomechanical and other in vitro and in vivo experiments, as it meticulously addresses fundamental characterization parameters crucial for medical device development. Research Highlights Support of optimum doping rates ions on hybrid composites and concentrations. Development of uniform surface appearance and distributions/orientations of microcrystals on ceramic compounds Improvement of cell viability and desired increase in biocompatibility with the doping of HA.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

ZirconiumAlloysBiocompatible MaterialsTitaniumCeramicsMaterials TestingCell SurvivalDurapatiteAnimalsX-Ray DiffractionPowdersMiceHumans

Stichwörter der Autor:innen

Ti‐6Al‐4VZrO2biocompatibilitycytotoxicityhydroxyapatite

Substanzen

ZirconiumAlloyszirconium oxideBiocompatible MaterialsTitaniumtitanium alloy (TiAl6V4)DurapatitePowders

Autor:innen und Institutionen

  • Department of Electricity and Energy, Kırıkkale University, Kırıkkale Vocational School, Kırıkkale, Turkey.
  • Department of Electronics and Automation, Kırıkkale University, Kırıkkale Vocational School, Kırıkkale, Turkey.
  • Hitit University, Scientific Technological Application and Research Center, Türkiye.
  • Department of Motor Vehicles and Transportation, Kırıkkale University, Kırıkkale Vocational School, Kırıkkale, Turkey.
  • Faculty of Engineering and Natural Sciences, Department of Electrical and Electronics Engineering, Kırıkkale University, Kırıkkale, Turkey.

ORCID-Profile: Muharrem Pul, Ümit Erdem

Förderung

  • Kırıkkale University Scientific Research Projects Unit

Zitieren

APA

Pul, M., Erdem, Ü., Bozer, B. M., Şimşek, T., Yılmazel, R., & Erten, M. Y. (2024). Synthesis of biocompatible Ti ‐ 6Al ‐ 4V composite reinforced with ZrO 2 and bioceramic produced by powder metallurgy: Morphological, structural, and biocompatibility analysis. Microscopy Research and Technique. https://doi.org/10.1002/jemt.24646

Vancouver

Pul M, Erdem Ü, Bozer BM, Şimşek T, Yılmazel R, Erten MY. Synthesis of biocompatible Ti ‐ 6Al ‐ 4V composite reinforced with ZrO 2 and bioceramic produced by powder metallurgy: Morphological, structural, and biocompatibility analysis. Microscopy Research and Technique. 2024. doi:10.1002/jemt.24646

BibTeX
@article{Pul2024,
  author = {Pul, Muharrem and Erdem, Ümit and Bozer, Büşra Moran and Şimşek, Tuncay and Yılmazel, Rüstem and Erten, Mustafa Yasin},
  title = {Synthesis of biocompatible Ti ‐ 6Al ‐ 4V composite reinforced with ZrO 2 and bioceramic produced by powder metallurgy: Morphological, structural, and biocompatibility analysis},
  journal = {Microscopy Research and Technique},
  year = {2024},
  doi = {10.1002/jemt.24646}
}
Kostenlos starten →