EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Investigating the Impact of Fused Filament Fabrication Process Parameters on the Compressive Properties of Porous PEEK and PEKK Biomaterials

Abigail E Tetteh iD, James A Smith iD, Daniel A Porter iD, Matthew A Di Prima iD, Steven M Kurtz iD

Journal of Biomedical Materials Research Part A · 2026-03 · 114 (3)

DOI: 10.1002/jbm.a.70053 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part A, online erschienen am 09.03.2026. Verfasst von Abigail E Tetteh und 4 weiteren Autor:innen. Beteiligte Einrichtung: School of Biomedical Engineering, Science and Health Systems, Implant Research Core, Drexel University, Philadelphia, Pennsylvania, USA. Hauptthemen laut MEDLINE: Ketones, Polyethylene Glycols, Biocompatible Materials, Compressive Strength. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 68 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: National Science Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Additive manufacturing (AM) can create orthopedic devices with integrated porosity that enables bone fixation post‐implantation. While porosity is key in promoting bone ingrowth and long‐term fixation, the device must provide adequate mechanical strength and functionality. Since AM process parameters dictate the final mechanical performance of printed parts, identifying key process parameter levels that preserve or improve such behavior in load‐bearing devices with integrated porosity is essential. Using a Taguchi design of experiments, gyroid‐structured polyether‐ether‐ketone (PEEK) and polyether‐ketone‐ketone (PEKK) specimens were fabricated via fused filament fabrication (FFF) AM to examine the impact of nozzle temperature ( T N ), chamber temperature ( T Ch ), and layer height (LH) on their compressive mechanical behavior. In addition to compression testing, the printed specimens were analyzed using optical microscopy, scanning electron microscopy, and micro‐computed tomography. Elevated processing conditions, specifically high T Ch combined with thick LH, can enhance heat retention, slow crystallization, increase strut thickness, and improve bonding at strut junctions, enabling porous PEEK and PEKK to withstand higher compressive loads. The elastic moduli of all the porous specimens were more sensitive to variations in processing conditions than their yield strength. Notably, the more amorphous PEKK specimens achieved over 87%–88% of PEEK's calculated elastic modulus in this study and 87%–90% of the yield strength without undergoing annealing. These results are promising, considering that, like PEEK, the elastic modulus of the porous PEKK fell within the range of trabecular bone, while its yield strength surpassed that of trabecular bone.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

KetonesPolyethylene GlycolsBiocompatible MaterialsCompressive StrengthMaterials TestingPorosityPolyether CompoundsBenzophenonesPolymersTemperature

Stichwörter der Autor:innen

Taguchi design of experimentadditive manufacturingcompressive propertiesfused filament fabricationpolyether‐ether‐ketonepolyether‐ketone‐ketoneporous

Substanzen

Polyether CompoundsKetonesBenzophenonesPolyethylene GlycolspolyetheretherketoneBiocompatible MaterialsPolymers

Autor:innen und Institutionen

  • School of Biomedical Engineering, Science and Health Systems, Implant Research Core, Drexel University, Philadelphia, Pennsylvania, USA.
  • Division of Applied Mechanics, Office of Science and Engineering Laboratories, Center for Devices and Radiological Health, United States Food and Drug Administration, Silver Spring, Maryland, USA.

ORCID-Profile: Abigail E Tetteh, James A Smith, Daniel A Porter, Matthew A Di Prima, Steven M Kurtz

Förderung

  • National Science Foundation

Zitieren

APA

Tetteh, A. E., Smith, J. A., Porter, D. A., Di Prima, M. A., & Kurtz, S. M. (2026). Investigating the Impact of Fused Filament Fabrication Process Parameters on the Compressive Properties of Porous PEEK and PEKK Biomaterials. Journal of Biomedical Materials Research Part A, 114(3). https://doi.org/10.1002/jbm.a.70053

Vancouver

Tetteh AE, Smith JA, Porter DA, Di Prima MA, Kurtz SM. Investigating the Impact of Fused Filament Fabrication Process Parameters on the Compressive Properties of Porous PEEK and PEKK Biomaterials. Journal of Biomedical Materials Research Part A. 2026;114(3). doi:10.1002/jbm.a.70053

BibTeX
@article{Tetteh2026,
  author = {Tetteh, Abigail E and Smith, James A and Porter, Daniel A and Di Prima, Matthew A and Kurtz, Steven M},
  title = {Investigating the Impact of Fused Filament Fabrication Process Parameters on the Compressive Properties of Porous PEEK and PEKK Biomaterials},
  journal = {Journal of Biomedical Materials Research Part A},
  year = {2026},
  volume = {114},
  number = {3},
  doi = {10.1002/jbm.a.70053}
}
Kostenlos starten →