EUVIMEDEUVIMED entdecken
Open Access

3D printing modality effect: Distinct printing outcomes dependent on selective laser sintering ( SLS ) and melt extrusion

Jeong Hun Park iD, Sarah Jo Tucker, Jeong-Kee Yoon, YongTae Kim, Scott J Hollister

Journal of Biomedical Materials Research Part A · 2024

DOI: 10.1002/jbm.a.37682 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Biomedical Materials Research Part A, 2024. Verfasst von Jeong Hun Park und 4 weiteren Autor:innen. Beteiligte Einrichtung: Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology and Emory University, Atlanta, Georgia, USA. Hauptthemen laut MEDLINE: Printing, Three-Dimensional, Lasers, Polyesters, Durapatite. Die Arbeit wurde bisher 12-mal zitiert (Crossref) und nennt 35 Literaturangaben. Der Volltext ist frei in PubMed Central verfügbar. Gefördert von: NICHD NIH HHS, NIH HHS, National Institutes of Health.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

A direct and comprehensive comparative study on different 3D printing modalities was performed. We employed two representative 3D printing modalities, laser‐ and extrusion‐based, which are currently used to produce patient‐specific medical implants for clinical translation, to assess how these two different 3D printing modalities affect printing outcomes. The same solid and porous constructs were created from the same biomaterial, a blend of 96% poly‐ε‐caprolactone (PCL) and 4% hydroxyapatite (HA), using two different 3D printing modalities. Constructs were analyzed to assess their printing characteristics, including morphological, mechanical, and biological properties. We also performed an in vitro accelerated degradation study to compare their degradation behaviors. Despite the same input material, the 3D constructs created from different 3D printing modalities showed distinct differences in morphology, surface roughness and internal void fraction, which resulted in different mechanical properties and cell responses. In addition, the constructs exhibited different degradation rates depending on the 3D printing modalities. Given that each 3D printing modality has inherent characteristics that impact printing outcomes and ultimately implant performance, understanding the characteristics is crucial in selecting the 3D printing modality to create reliable biomedical implants.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Printing, Three-DimensionalLasersPolyestersDurapatiteMaterials TestingPorosityAnimalsHumansBiocompatible MaterialsTissue ScaffoldsMice

Stichwörter der Autor:innen

3D printing3D printing characteristicsmelt extrusion 3D printingpoly‐ε‐caprolactone (PCL)selective laser sintering

Substanzen

polycaprolactonePolyestersDurapatiteBiocompatible Materials

Autor:innen und Institutionen

  • Wallace H. Coulter Department of Biomedical Engineering, Georgia Institute of Technology and Emory University, Atlanta, Georgia, USA.
  • Center for 3D Medical Fabrication, Georgia Institute of Technology and Emory University, Atlanta, Georgia, USA.
  • Global Center for Medical Innovation, Atlanta, Georgia, USA.
  • Department of Systems Biotechnology, Chung-Ang University, Anseong-si, Gyeonggi-do, Republic of Korea.
  • George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia, USA.
  • Parker H. Petit Institute for Bioengineering and Bioscience (IBB), Georgia Institute of Technology, Atlanta, Georgia, USA.

ORCID-Profile: Jeong Hun Park

Förderung

  • NICHD NIH HHS
  • NIH HHS
  • National Institutes of Health

Zitieren

APA

Park, J. H., Tucker, S. J., Yoon, J. K., Kim, Y., & Hollister, S. J. (2024). 3D printing modality effect: Distinct printing outcomes dependent on selective laser sintering ( SLS ) and melt extrusion. Journal of Biomedical Materials Research Part A. https://doi.org/10.1002/jbm.a.37682

Vancouver

Park JH, Tucker SJ, Yoon JK, Kim Y, Hollister SJ. 3D printing modality effect: Distinct printing outcomes dependent on selective laser sintering ( SLS ) and melt extrusion. Journal of Biomedical Materials Research Part A. 2024. doi:10.1002/jbm.a.37682

BibTeX
@article{Park2024,
  author = {Park, Jeong Hun and Tucker, Sarah Jo and Yoon, Jeong-Kee and Kim, YongTae and Hollister, Scott J},
  title = {3D printing modality effect: Distinct printing outcomes dependent on selective laser sintering ( SLS ) and melt extrusion},
  journal = {Journal of Biomedical Materials Research Part A},
  year = {2024},
  doi = {10.1002/jbm.a.37682}
}
Kostenlos starten →