EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

The influence of Zircos‐E® etchant, silica coating, and alumina air‐particle abrasion on the debonding resistance of endocrowns with three different preparation designs

Ahmed Yaseen Alqutaibi iD, Mohammed Ahmed Alghauli iD, Karim Dewedar, Mohammed H AbdElaziz iD, Samah Saker iD

Clinical and Experimental Dental Research · 2024-06 · 10 (3)

DOI: 10.1002/cre2.901 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical and Experimental Dental Research, online erschienen am 21.05.2024. Verfasst von Ahmed Yaseen Alqutaibi und 4 weiteren Autor:innen. Beteiligte Einrichtung: Substitutive Dental Science Department, College of Dentistry, Taibah University, Al-Madinah, Saudi Arabia. Hauptthemen laut MEDLINE: Aluminum Oxide, Silicon Dioxide, Zirconium, Surface Properties. Die Arbeit wurde bisher 14-mal zitiert (Crossref) und nennt 54 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: None.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objectives

The study aimed to evaluate the debonding resistance of three different endocrown designs on molar teeth, using three different zirconia surface pretreatments. Material and Method Ninety human mandibular first molars were divided into three main groups: endocrowns without ferrule, with 1 mm ferrule, and with 2 mm ferrule. The subgroups were defined by their surface pretreatment method used ( n = 15): 50 μm alumina air‐particle abrasion, silica coating using 30 μm Cojet™ particles, and Zircos‐E® etching. The endocrowns were fabricated using multilayer zirconia ceramic, cemented with self‐adhesive resin cement, and subjected to 5000 thermocycles (5–55°C) before debonding. The data obtained were analyzed using a two‐way ANOVA.

Results

All test specimens survived the thermocyclic aging. The results indicated that both the preparation design and the surface treatment had a significant impact on the resistance to debonding of the endocrowns ( p < .001). The 2 mm ferrule followed by the 1 mm ferrule designs exhibited the highest debonding resistance, both were superior to the endocrown without ferrule. Zircos‐E® etching and silica coating yielded comparable debonding resistance, which were significantly higher than alumina air‐particle abrasion. All endocrowns demonstrated a favorable failure mode.

Conclusions

All designs and surface treatments showed high debonding resistance for a single restoration. However, ferrule designs with Zircos‐E® etching or silica coating may represent better clinical options compared to the nonferrule design or alumina airborne‐particle abrasion. Nonetheless, further research, including fatigue testing and evaluations with different luting agents is recommended.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Aluminum OxideSilicon DioxideZirconiumSurface PropertiesHumansMolarMaterials TestingAir Abrasion, DentalResin CementsDental EtchingDental Stress AnalysisDental Prosthesis Design

Stichwörter der Autor:innen

Zirconia endocrownsZircos‐E® etchairborne‐particle abrasiondebonding resistance

Substanzen

Aluminum OxideSilicon DioxideZirconiumResin Cementszirconium oxide

Autor:innen und Institutionen

  • Substitutive Dental Science Department, College of Dentistry, Taibah University, Al-Madinah, Saudi Arabia.
  • Department of Prosthodontics, Faculty of Dentistry, Ibb University, Ibb, Yemen.
  • Crown and Bridge Department, Faculty of Dental Medicine, Al-Azhar University, Cairo, Egypt.
  • Fixed Prosthodontic Department, Faculty of Dentistry, Mansoura University, Mansoura, Egypt.

ORCID-Profile: Ahmed Yaseen Alqutaibi, Mohammed Ahmed Alghauli, Mohammed H AbdElaziz, Samah Saker

Förderung

  • None

Zitieren

APA

Alqutaibi, A. Y., Alghauli, M. A., Dewedar, K., AbdElaziz, M. H., & Saker, S. (2024). The influence of Zircos‐E® etchant, silica coating, and alumina air‐particle abrasion on the debonding resistance of endocrowns with three different preparation designs. Clinical and Experimental Dental Research, 10(3). https://doi.org/10.1002/cre2.901

Vancouver

Alqutaibi AY, Alghauli MA, Dewedar K, AbdElaziz MH, Saker S. The influence of Zircos‐E® etchant, silica coating, and alumina air‐particle abrasion on the debonding resistance of endocrowns with three different preparation designs. Clinical and Experimental Dental Research. 2024;10(3). doi:10.1002/cre2.901

BibTeX
@article{Alqutaibi2024,
  author = {Alqutaibi, Ahmed Yaseen and Alghauli, Mohammed Ahmed and Dewedar, Karim and AbdElaziz, Mohammed H and Saker, Samah},
  title = {The influence of Zircos‐E® etchant, silica coating, and alumina air‐particle abrasion on the debonding resistance of endocrowns with three different preparation designs},
  journal = {Clinical and Experimental Dental Research},
  year = {2024},
  volume = {10},
  number = {3},
  doi = {10.1002/cre2.901}
}
Kostenlos starten →