EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Comparison of the marginal and internal fit of PMMA interim crowns printed with different layer thicknesses in 3D‐printing technique

Mahya Hasanzade iD, Negin Yaghoobi iD, Parsa Nematollahi, Rezvaneh Ghazanfari

Clinical and Experimental Dental Research · 2023

DOI: 10.1002/cre2.758 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Clinical and Experimental Dental Research, 2023. Verfasst von Mahya Hasanzade und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics, School of Dentistry, International Campus, Tehran University of Medical Sciences, Tehran, Iran. Hauptthemen laut MEDLINE: Polymethyl Methacrylate, Computer-Aided Design. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 49 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Objective

The aim of this in vitro study was to compare the effect of printing layer thickness on the marginal and internal fit of interim crowns. Material and methods A maxillary first molar model was prepared for ceramic restoration. Thirty‐six crowns were printed with three different layer thicknesses using a digital light processing‐based three‐dimensional printer (25, 50, and 100 µm [LT 25, LT 50, and LT 100]). The marginal and internal gaps of the crowns were measured with replica technique. An analysis of variance was conducted to determine if there were significant differences between the groups ( ɑ = .05).

Results

The marginal gap of LT 100 group was significantly higher than that LT 25 ( p = .002) and LT 50 groups ( p ≤ .001). The LT 25 group has significantly larger axial gaps than LT 50 group ( p = .013); however, there were no statistically significant differences between other groups. The LT 50 group showed the smallest axio‐occlusal gap. The mean occlusal gap differed significantly by printing layer thickness ( p ≤ .001), with the largest gap occurring for LT 100.

Conclusions

Provisional crowns printed with 50 µm layer thickness provided the best marginal and internal fit. Clinical significance It is recommended that provisional crowns be printed with a 50 µm layer thickness to ensure optimal marginal and internal fit.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Polymethyl MethacrylateComputer-Aided DesignDental Prosthesis DesignDental Marginal AdaptationCrownsPrinting, Three-Dimensional

Stichwörter der Autor:innen

3D-printinginterim dental prosthesesinternal adaptationmarginal adaptation

Substanzen

Polymethyl Methacrylate

Autor:innen und Institutionen

  • Department of Prosthodontics, School of Dentistry, International Campus, Tehran University of Medical Sciences, Tehran, Iran.
  • Department of Prosthodontics, School of Dentistry, Tehran University of Medical Sciences, Tehran, Iran.
  • School of Dentistry, International Campus, Tehran University of Medical Sciences, Tehran, Iran.

ORCID-Profile: Mahya Hasanzade, Negin Yaghoobi

Zitieren

APA

Hasanzade, M., Yaghoobi, N., Nematollahi, P., & Ghazanfari, R. (2023). Comparison of the marginal and internal fit of PMMA interim crowns printed with different layer thicknesses in 3D‐printing technique. Clinical and Experimental Dental Research. https://doi.org/10.1002/cre2.758

Vancouver

Hasanzade M, Yaghoobi N, Nematollahi P, Ghazanfari R. Comparison of the marginal and internal fit of PMMA interim crowns printed with different layer thicknesses in 3D‐printing technique. Clinical and Experimental Dental Research. 2023. doi:10.1002/cre2.758

BibTeX
@article{Hasanzade2023,
  author = {Hasanzade, Mahya and Yaghoobi, Negin and Nematollahi, Parsa and Ghazanfari, Rezvaneh},
  title = {Comparison of the marginal and internal fit of PMMA interim crowns printed with different layer thicknesses in 3D‐printing technique},
  journal = {Clinical and Experimental Dental Research},
  year = {2023},
  doi = {10.1002/cre2.758}
}
Kostenlos starten →