Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer
International Journal of Ceramic Engineering & Science · 2020-11 · 2 (6) · 320-331
DOI: 10.1002/ces2.10070 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of Ceramic Engineering & Science, online erschienen am 27.09.2020. Verfasst von Corson L. Cramer und 7 weiteren Autor:innen. Die Arbeit wurde bisher 44-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Advanced Research Projects Agency - Energy.
Abstract (Originalsprache)
The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP is reported. The density, Young's modulus and flexural strength of disk‐shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young's modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar‐L/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after three PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.
Förderung
- Advanced Research Projects Agency - Energy
Zitieren
APA
Cramer, C. L., Armstrong, H., Flores‐Betancourt, A., Han, L., Elliott, A. M., Lara‐Curzio, E., Saito, T., & Nawaz, K. (2020). Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer. International Journal of Ceramic Engineering & Science, 2(6), 320-331. https://doi.org/10.1002/ces2.10070
Vancouver
Cramer CL, Armstrong H, Flores‐Betancourt A, Han L, Elliott AM, Lara‐Curzio E, et al. Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer. International Journal of Ceramic Engineering & Science. 2020;2(6):320-331. doi:10.1002/ces2.10070
BibTeX
@article{Cramer2020,
author = {Cramer, Corson L. and Armstrong, Herb and Flores‐Betancourt, Alexis and Han, Lu and Elliott, Amy M. and Lara‐Curzio, Edgar and Saito, Tomonori and Nawaz, Kashif},
title = {Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer},
journal = {International Journal of Ceramic Engineering & Science},
year = {2020},
volume = {2},
number = {6},
pages = {320--331},
doi = {10.1002/ces2.10070}
}
EUVIMED