Application of HoloLens ‐based augmented reality and three‐dimensional printed anatomical tooth reference models in dental education
Anatomical Sciences Education · 2023-07 · 16 (4) · 743-755
DOI: 10.1002/ase.2241 ↗Kurz gefasst
Fachartikel in der Zeitschrift Anatomical Sciences Education, online erschienen am 28.12.2022. Verfasst von Piotr Grad und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Integrated Dentistry, Institute of Dentistry, Faculty of Medicine, Jagiellonian University Medical College, Kraków, Poland. Hauptthemen laut MEDLINE: Augmented Reality, Anatomy. Die Arbeit wurde bisher 34-mal zitiert (Crossref) und nennt 57 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Uniwersytet Jagielloński Collegium Medicum.
Abstract (Originalsprache)
Tooth anatomy is fundamental knowledge used in everyday dental practice to reconstruct the occlusal surface during cavity fillings. The main objective of this project was to evaluate the suitability of two types of anatomical tooth reference models used to support reconstruction of the occlusal anatomy of the teeth: (1) a three‐dimensional (3D)‐printed model and (2) a model displayed in augmented reality (AR) using Microsoft HoloLens. The secondary objective was to evaluate three aspects impacting the outcome: clinical experience, comfort of work, and other variables. The tertiary objective was to evaluate the usefulness of AR in dental education. Anatomical models of crowns of three different molars were made using cone beam computed tomography image segmentation, printed with a stereolithographic 3D‐printer, and then displayed in the HoloLens. Each participant reconstructed the occlusal anatomy of three teeth. One without any reference materials and two with an anatomical reference model, either 3D‐printed or holographic. The reconstruction work was followed by the completion of an evaluation questionnaire. The maximum Hausdorff distances (Hmax) between the superimposed images of the specimens after the procedures and the anatomical models were then calculated. The results showed that the most accurate but slowest reconstruction was achieved with the use of 3D‐printed reference models and that the results were not affected by other aspects considered. For this method, the Hmax was observed to be 630 μm ( p = 0.004). It was concluded that while AR models can be helpful in dental anatomy education, they are not suitable replacements for physical models.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Integrated Dentistry, Institute of Dentistry, Faculty of Medicine, Jagiellonian University Medical College, Kraków, Poland.
- Department of Bioinformatics and Telemedicine, Faculty of Medicine, Jagiellonian University Medical College, Kraków, Poland.
- Department of Radiology, New York University Grossman School of Medicine, New York, New York, USA.
- Department of Biophysics, Chair of Physiology, Faculty of Medicine, Jagiellonian University Medical College, Kraków, Poland.
ORCID-Profile: Piotr Grad, Anna M Przeklasa-Bierowiec, Krzysztof P Malinowski, Klaudia Proniewska, Grzegorz Tatoń
Förderung
- Uniwersytet Jagielloński Collegium Medicum
Zitieren
APA
Grad, P., Przeklasa-Bierowiec, A. M., Malinowski, K. P., Witowski, J., Proniewska, K., & Tatoń, G. (2023). Application of HoloLens ‐based augmented reality and three‐dimensional printed anatomical tooth reference models in dental education. Anatomical Sciences Education, 16(4), 743-755. https://doi.org/10.1002/ase.2241
Vancouver
Grad P, Przeklasa-Bierowiec AM, Malinowski KP, Witowski J, Proniewska K, Tatoń G. Application of HoloLens ‐based augmented reality and three‐dimensional printed anatomical tooth reference models in dental education. Anatomical Sciences Education. 2023;16(4):743-755. doi:10.1002/ase.2241
BibTeX
@article{Grad2023,
author = {Grad, Piotr and Przeklasa-Bierowiec, Anna M and Malinowski, Krzysztof P and Witowski, Jan and Proniewska, Klaudia and Tatoń, Grzegorz},
title = {Application of HoloLens ‐based augmented reality and three‐dimensional printed anatomical tooth reference models in dental education},
journal = {Anatomical Sciences Education},
year = {2023},
volume = {16},
number = {4},
pages = {743--755},
doi = {10.1002/ase.2241}
}
EUVIMED