EUVIMEDEUVIMED entdecken
Crossref

Thermal Annealing of Injection‐Molded PLA Grades: Trade‐Offs Between Crystallinity Development, Dimensional Stability, Secondary Shrinkage, and Mechanical Performance

Edson A. dos Santos Filho, Edda Valentina Veracierta Rodriguez, Simon Debrie, Guilhermino J. M. Fechine, Edcleide M. Araujo, Ludwig Cardon, Mariya Edeleva

Journal of Applied Polymer Science · 05.10.2026 · 143 (37)

DOI: 10.1002/app.71150 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Applied Polymer Science, online erschienen am 05.07.2026. Verfasst von Edson A. dos Santos Filho und 6 weiteren Autor:innen. Die Arbeit nennt 41 Literaturangaben. Gefördert von: Conselho Nacional de Desenvolvimento Científico e Tecnológico.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Injection molding is widely used for polymer components, yet producing dimensionally accurate poly(lactic acid) (PLA) parts remains challenging because shrinkage and warpage arise from thermal contraction, crystallization‐induced densification, and relaxation of frozen‐in amorphous structure. Post‐molding annealing can increase crystallinity and heat resistance, but may also induce secondary shrinkage and embrittlement. Here, two commercial injection‐molding PLA grades with different crystallization behavior were processed under identical molding and packing conditions, while only the annealing protocol was varied between 60°C and 120°C. DSC showed different crystallization tendencies after thermal‐history erasure, with crystallinity of approximately 3% for PLA_a and 20% for PLA_c, although as‐molded specimens showed similar crystallinity of 14%–17%. Isothermal DSC confirmed faster crystallization of PLA_c, with half‐times 3–5 times shorter than PLA_a at 100°C and 120°C. Annealing increased crystallinity to approximately 68% for PLA_c and 50% for PLA_a after 3 h at 120°C. However, PLA_a showed stronger secondary shrinkage, reaching 2%–2.3%, whereas PLA_c remained below 1%. Enthalpy‐recovery analysis, POM, SEM, MFI, TGA, and FTIR demonstrate that annealing produces a grade‐dependent trade‐off between crystallinity, dimensional accuracy, and mechanical performance. Impact strength peaks at 90°C, whereas tensile performance decreases at 120°C, confirming crystallinity alone cannot predict dimensional stability reliably.

Förderung

  • Conselho Nacional de Desenvolvimento Científico e Tecnológico

Zitieren

APA

Filho, E. A. D. S., Rodriguez, E. V. V., Debrie, S., Fechine, G. J. M., Araujo, E. M., Cardon, L., & Edeleva, M. (2026). Thermal Annealing of Injection‐Molded PLA Grades: Trade‐Offs Between Crystallinity Development, Dimensional Stability, Secondary Shrinkage, and Mechanical Performance. Journal of Applied Polymer Science, 143(37). https://doi.org/10.1002/app.71150

Vancouver

Filho EADS, Rodriguez EVV, Debrie S, Fechine GJM, Araujo EM, Cardon L, et al. Thermal Annealing of Injection‐Molded PLA Grades: Trade‐Offs Between Crystallinity Development, Dimensional Stability, Secondary Shrinkage, and Mechanical Performance. Journal of Applied Polymer Science. 2026;143(37). doi:10.1002/app.71150

BibTeX
@article{Filho2026,
  author = {Filho, Edson A. dos Santos and Rodriguez, Edda Valentina Veracierta and Debrie, Simon and Fechine, Guilhermino J. M. and Araujo, Edcleide M. and Cardon, Ludwig and Edeleva, Mariya},
  title = {Thermal Annealing of Injection‐Molded PLA Grades: Trade‐Offs Between Crystallinity Development, Dimensional Stability, Secondary Shrinkage, and Mechanical Performance},
  journal = {Journal of Applied Polymer Science},
  year = {2026},
  volume = {143},
  number = {37},
  doi = {10.1002/app.71150}
}
Kostenlos starten →