EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Decolorization of Lignin for High‐Resolution 3D Printing of High Lignin‐Content Composites

David Böcherer iD, Ramin Montazeri, Yuanyuan Li, Silvio Tisato, Leonhard Hambitzer, Dorothea Helmer iD

Advanced Science · 2024-10 · 11 (39)

DOI: 10.1002/advs.202406311 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Science, online erschienen am 13.08.2024. Verfasst von David Böcherer und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Microsystems Engineering, University of Freiburg, 79110, Freiburg, Germany. Die Arbeit wurde bisher 24-mal zitiert (Crossref) und nennt 47 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Research Cluster "Interactive and Programmable Materials", IPROM, Carl Zeiss Foundation.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Lignin, one of the most abundant biomaterials and a large‐scale industrial waste product, is a promising filler for polymers as it reduces the amount of fossil resources and is readily available. 3D printing is well‐known for producing detailed polymer structures in small sizes at low waste production. Especially light‐assisted 3D printing is a powerful technique for production of high‐resolution structures. However, lignin acts as a very efficient absorber for UV and visible light limiting the printability of lignin composites, reducing its potential as a high‐volume filler. In this work, the decolorization of lignin is presented for high‐resolution 3D printing of biocomposites with lignin content up to 40 wt.%. Organosolv lignin (OSL) is decolorized by an optimized low‐energy process of acetylation and subsequent UV irradiation reducing the UV absorbance by 71%. By integration of decolorized lignin into bio‐based tetrahydrofurfuryl acrylate (THFA), a lignin content of 40 wt.% and a resolution of 250 µm is achieved. Due to the reinforcing properties of lignin, the stiffness and strength of the material is increased by factors of 15 and 2.3, respectively. This work paves the way for the re‐use of a large amount of lignin waste for 3D printing of tough materials at high resolution.

Schlagwörter

Stichwörter der Autor:innen

decolorization of ligninhigh‐resolution 3D printinglignin biocomposites

Autor:innen und Institutionen

  • Department of Microsystems Engineering, University of Freiburg, 79110, Freiburg, Germany.
  • Freiburg Materials Research Center (FMF), University of Freiburg, 79104, Freiburg, Germany.

ORCID-Profile: David Böcherer, Dorothea Helmer

Förderung

  • Research Cluster "Interactive and Programmable Materials"
  • IPROM
  • Carl Zeiss Foundation
  • Carl-Zeiss-Stiftung

Zitieren

APA

Böcherer, D., Montazeri, R., Li, Y., Tisato, S., Hambitzer, L., & Helmer, D. (2024). Decolorization of Lignin for High‐Resolution 3D Printing of High Lignin‐Content Composites. Advanced Science, 11(39). https://doi.org/10.1002/advs.202406311

Vancouver

Böcherer D, Montazeri R, Li Y, Tisato S, Hambitzer L, Helmer D. Decolorization of Lignin for High‐Resolution 3D Printing of High Lignin‐Content Composites. Advanced Science. 2024;11(39). doi:10.1002/advs.202406311

BibTeX
@article{Bcherer2024,
  author = {Böcherer, David and Montazeri, Ramin and Li, Yuanyuan and Tisato, Silvio and Hambitzer, Leonhard and Helmer, Dorothea},
  title = {Decolorization of Lignin for High‐Resolution 3D Printing of High Lignin‐Content Composites},
  journal = {Advanced Science},
  year = {2024},
  volume = {11},
  number = {39},
  doi = {10.1002/advs.202406311}
}
Kostenlos starten →