EUVIMEDEUVIMED entdecken
Crossref

3D Printing of Ultrahigh Filler Content Composites Enabled by Granular Hydrogels

Chen Cui, Ze-Yong Zhuang, Huai-Ling Gao, Jun Pang, Xiao-Feng Pan, Shu-Hong Yu iD

Advanced Materials · 2025-07 · 37 (30)

DOI: 10.1002/adma.202500782 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials, online erschienen am 09.05.2025. Verfasst von Chen Cui und 5 weiteren Autor:innen. Beteiligte Einrichtung: Shenzhen Key Laboratory of Sustainable Biomimetic Materials, Guangdong Provincial Key Laboratory of Sustainable Biomimetic Materials and Green Energy…. Die Arbeit wurde bisher 21-mal zitiert (Crossref) und nennt 56 Literaturangaben. Gefördert von: Shenzhen Science and Technology Program, National Natural Science Foundation of China, Guangdong Provincial Key Laboratory of Sustainable Biomimetic Materials and Green Energy.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Ultrahigh filler content composites have exhibited distinctive properties in various areas, such as structural materials, electrical insulation, thermal management, and energy storage devices. However, manufacturing 3D composites with ultrahigh filler content is challenging because excessive fillers have compromised the processing flowability of the composite. Here, using hollow glass microspheres (HGMs) as an example filler, a 3D printing strategy for fabricating particulate composites with ultrahigh HGM content (up to 99.2 wt.%) is reported. By incorporating the highly swollen granular hydrogel as the shear sliding phase between HGMs, the probability of clogging during extrusion of the composite ink with ultrahigh HGM content is substantially reduced. A quantitative phase diagram is developed to optimally choose the ink compositions with the maximum HGM content, as well as printing parameters. The resulting composite with ultrahigh HGM content shows ceramic‐foam‐like brittle fracture behavior, high wave‐transparent properties (0.996), and low thermal conductivity (0.045 W m −1 K −1 ). Further, a thermal shield with high HGM content on a microcircuit board to validate the localized thermal protection is fabricated. It is believed that incorporating hydrogel matrix into the printing ink will unlock the capabilities of 3D printed ultrahigh filler content composites in creating more intricate structures with advanced functionalities.

Schlagwörter

Stichwörter der Autor:innen

3D printingclogging behaviorgranular hydrogelultrahigh filler content composites

Autor:innen und Institutionen

  • Shenzhen Key Laboratory of Sustainable Biomimetic Materials, Guangdong Provincial Key Laboratory of Sustainable Biomimetic Materials and Green Energy, Department of Materials Science and Engineering, Department of Chemi…
  • CAS Key Laboratory of Mechanical Behavior and Design of Materials, Department of Modern Mechanics, University of Science and Technology of China, Hefei, Anhui, 230027, China.
  • Department of Chemistry, New Cornerstone Science Laboratory, Institute of Biomimetic Materials & Chemistry, Anhui Engineering Laboratory of Biomimetic Materials, Division of Nanomaterials & Chemistry, Hefei National Res…

ORCID-Profile: Shu-Hong Yu

Förderung

  • Shenzhen Science and Technology Program
  • National Natural Science Foundation of China
  • Guangdong Provincial Key Laboratory of Sustainable Biomimetic Materials and Green Energy
  • New Cornerstone Science Foundation
  • National Key Research and Development Program of China
  • High level of special funds
  • Shenzhen Science and Technology Innovation Program

Zitieren

APA

Cui, C., Zhuang, Z. Y., Gao, H. L., Pang, J., Pan, X. F., & Yu, S. H. (2025). 3D Printing of Ultrahigh Filler Content Composites Enabled by Granular Hydrogels. Advanced Materials, 37(30). https://doi.org/10.1002/adma.202500782

Vancouver

Cui C, Zhuang ZY, Gao HL, Pang J, Pan XF, Yu SH. 3D Printing of Ultrahigh Filler Content Composites Enabled by Granular Hydrogels. Advanced Materials. 2025;37(30). doi:10.1002/adma.202500782

BibTeX
@article{Cui2025,
  author = {Cui, Chen and Zhuang, Ze-Yong and Gao, Huai-Ling and Pang, Jun and Pan, Xiao-Feng and Yu, Shu-Hong},
  title = {3D Printing of Ultrahigh Filler Content Composites Enabled by Granular Hydrogels},
  journal = {Advanced Materials},
  year = {2025},
  volume = {37},
  number = {30},
  doi = {10.1002/adma.202500782}
}
Kostenlos starten →