EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Stopping a Multilayered Co‐Axial Flow in a 3D Printed Microchannel with Cascaded Nozzles

Helen Werner, Ebrahim TaiediNejad, Mehmet Akif Sahin, Moritz Leuthner, Peer Erfle, Oliver Hayden, Andreas Dietzel, Ghulam Destgeer

Advanced Materials Technologies · 2025-08 · 10 (16)

DOI: 10.1002/admt.202500203 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials Technologies, online erschienen am 15.04.2025. Verfasst von Helen Werner und 7 weiteren Autor:innen. Die Arbeit wurde bisher 8-mal zitiert (Crossref) und nennt 38 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Deutsche Forschungsgemeinschaft.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Three different flow control methods are investigated to stop a multilayered flow inside a 3D‐printed microfluidic channel by bringing the average flow velocity from >100 mm s −1 to below a critical velocity of 200 µm s −1 within a certain delay time t d of ≈2 s. A sequence of three concentric nozzles is 3D printed (≈75 µm) and embedded serially inside the microchannel (≈200 µm) using a two‐photon polymerization method. The 3D printed device produces a structured coaxial flow of four streams with individual layer thicknesses of O (10 µm). The pressure gradient across the fluidic circuit is removed, from > 2 bar to ≈0 bar, to stop the multilayered flow and measure t d to assess the performance of the three stop‐flow methods. During the stop‐flow phase, an inhomogeneous pressure gradient across different inlets resulted in a backflow to inlet channels with lower pressures. The fluidic capacitance is systematically managed to minimize a dimensionless backflow index ( BFI ) value from ≈0.3 (worst case) to ≈0.03 (best case) for a total flow rate ranging from 16.8 to 168 µL min −1 . Finally, the best stop‐flow conditions are recommended, which resulted in a minimal delay time of t d ≈ 2 s and a BFI < 0.05.

Förderung

  • Deutsche Forschungsgemeinschaft

Zitieren

APA

Werner, H., TaiediNejad, E., Sahin, M. A., Leuthner, M., Erfle, P., Hayden, O., Dietzel, A., & Destgeer, G. (2025). Stopping a Multilayered Co‐Axial Flow in a 3D Printed Microchannel with Cascaded Nozzles. Advanced Materials Technologies, 10(16). https://doi.org/10.1002/admt.202500203

Vancouver

Werner H, TaiediNejad E, Sahin MA, Leuthner M, Erfle P, Hayden O, et al. Stopping a Multilayered Co‐Axial Flow in a 3D Printed Microchannel with Cascaded Nozzles. Advanced Materials Technologies. 2025;10(16). doi:10.1002/admt.202500203

BibTeX
@article{Werner2025,
  author = {Werner, Helen and TaiediNejad, Ebrahim and Sahin, Mehmet Akif and Leuthner, Moritz and Erfle, Peer and Hayden, Oliver and Dietzel, Andreas and Destgeer, Ghulam},
  title = {Stopping a Multilayered Co‐Axial Flow in a 3D Printed Microchannel with Cascaded Nozzles},
  journal = {Advanced Materials Technologies},
  year = {2025},
  volume = {10},
  number = {16},
  doi = {10.1002/admt.202500203}
}
Kostenlos starten →