3D‐Printed Microinjection Needle Arrays via a Hybrid DLP‐Direct Laser Writing Strategy
Advanced Materials Technologies · 2023-03 · 8 (5)
DOI: 10.1002/admt.202201641 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Materials Technologies, online erschienen am 05.02.2023. Verfasst von Sunandita Sarker und 11 weiteren Autor:innen. Beteiligte Einrichtung: Department of Mechanical Engineering, University of Maryland, College Park, MD 20742, USA; Maryland Robotics Center, University of Maryland, College …. Die Arbeit wurde bisher 49-mal zitiert (Crossref) und nennt 92 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: NIA NIH HHS, NIBIB NIH HHS, NINDS NIH HHS.
Abstract (Originalsprache)
Microinjection protocols are ubiquitous throughout biomedical fields, with hollow microneedle arrays (MNAs) offering distinctive benefits in both research and clinical settings. Unfortunately, manufacturing‐associated barriers remain a critical impediment to emerging applications that demand high‐density arrays of hollow, high‐aspect‐ratio microneedles. To address such challenges, here, a hybrid additive manufacturing approach that combines digital light processing (DLP) 3D printing with “ex situ direct laser writing ( es DLW)” is presented to enable new classes of MNAs for fluidic microinjections. Experimental results for es DLW‐based 3D printing of arrays of high‐aspect‐ratio microneedles—with 30 µm inner diameters, 50 µm outer diameters, and 550 µm heights, and arrayed with 100 µm needle‐to‐needle spacing—directly onto DLP‐printed capillaries reveal uncompromised fluidic integrity at the MNA‐capillary interface during microfluidic cyclic burst‐pressure testing for input pressures in excess of 250 kPa ( n = 100 cycles). Ex vivo experiments perform using excised mouse brains reveal that the MNAs not only physically withstand penetration into and retraction from brain tissue but also yield effective and distributed microinjection of surrogate fluids and nanoparticle suspensions directly into the brains. In combination, the results suggest that the presented strategy for fabricating high‐aspect‐ratio, high‐density, hollow MNAs could hold unique promise for biomedical microinjection applications.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Mechanical Engineering, University of Maryland, College Park, MD 20742, USA; Maryland Robotics Center, University of Maryland, College Park, MD 20742, USA; Institute for Systems Research, University of Mar…
- Department of Mechanical Engineering, University of Maryland, College Park, MD 20742, USA.
- Department of Chemical and Biomolecular Engineering, University of Maryland, College Park, MD 20742, USA.
- Program in Image Guided Neurointerventions, Department of Diagnostic Radiology and Nuclear Medicine, University of Maryland School of Medicine, Baltimore, MD 21201, USA.
Förderung
- NIA NIH HHS
- NIBIB NIH HHS
- NINDS NIH HHS
- NIDDK NIH HHS
- National Institutes of Health
- Maryland Stem Cell Research Fund
- National Science Foundation
- National Institute on Aging
Zitieren
APA
Sarker, S., Colton, A., Wen, Z., Xu, X., Erdi, M., Jones, A., Kofinas, P., Tubaldi, E., Walczak, P., Janowski, M., Liang, Y., & Sochol, R. D. (2023). 3D‐Printed Microinjection Needle Arrays via a Hybrid DLP‐Direct Laser Writing Strategy. Advanced Materials Technologies, 8(5). https://doi.org/10.1002/admt.202201641
Vancouver
Sarker S, Colton A, Wen Z, Xu X, Erdi M, Jones A, et al. 3D‐Printed Microinjection Needle Arrays via a Hybrid DLP‐Direct Laser Writing Strategy. Advanced Materials Technologies. 2023;8(5). doi:10.1002/admt.202201641
BibTeX
@article{Sarker2023,
author = {Sarker, Sunandita and Colton, Adira and Wen, Ziteng and Xu, Xin and Erdi, Metecan and Jones, Anthony and Kofinas, Peter and Tubaldi, Eleonora and Walczak, Piotr and Janowski, Miroslaw and Liang, Yajie and Sochol, Ryan D},
title = {3D‐Printed Microinjection Needle Arrays via a Hybrid DLP‐Direct Laser Writing Strategy},
journal = {Advanced Materials Technologies},
year = {2023},
volume = {8},
number = {5},
doi = {10.1002/admt.202201641}
}
EUVIMED