EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Traceless Photopolymerization with Non‐Pulsed Red Light Enables 3D‐Printable Cell‐Laden Hydrogels

Ali Eftekhari, Kelsey Rianne de Graaf, Ekaterina Takmakova, Hatai Jongprasitkul, Alexander Efimov, Sanna Turunen, Andrew Kerr, Minna Kellomäki, Robert Luxenhofer, Timo Laaksonen, Nikita Durandin iD

Advanced Materials · 2025

DOI: 10.1002/adma.202502386 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Materials, 2025. Verfasst von Ali Eftekhari und 10 weiteren Autor:innen. Beteiligte Einrichtung: Faculty of Engineering and Natural Sciences, Tampere University, Tampere, 33720, Finland. Hauptthemen laut MEDLINE: Hydrogels, Polymerization, Light, Printing, Three-Dimensional. Die Arbeit wurde bisher 20-mal zitiert (Crossref) und nennt 59 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: Academy of Finland, SUSBIO PROFI7, H2020 European Research Council.

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Photocrosslinking of hydrogels with non‐pulsed red light offers improved biocompatibility and deep tissue penetration in contrast to traditional UV‐initiated methods. However, hydrogels fabricated upon red‐light excitation are always colored by a photoinitiator, limiting their use in applications requiring high optical transparency, such as (bio)sensors, ophthalmological applications, or wound dressings. Additionally, the cytotoxicity of a photoinitiator is always a concern, especially in bioapplications. Herein, a photoinitiating system composed of an FDA‐approved methylene blue photosensitizer and cytocompatible triethanolamine is introduced. The system can induce photopolymerization upon 625 nm irradiation and leaves no visible trace of the methylene blue color afterward, thus named “traceless”. With this approach, gelatine methacrylate hydrogel is successfully polymerized under ambient conditions. The hydrogel is permanently colorless with well‐controlled stiffness due to the light‐dependent nature of the polymerization process. The system is further successfully applied in extrusion‐based 3D‐bioprinting with NIH‐3T3 fibroblasts, followed by photocuring to produce cell‐laden 3D structures, indicating its potential for tissue engineering. Upon culturing the cell‐laden constructs, the fibroblasts are able to proliferate and adhere to the hydrogel material. The red‐light excitation enables polymerization through at least 5 mm of biological tissue, projecting, inter alia, its use for transdermal photopolymerization in minimally invasive implantation.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

HydrogelsPolymerizationLightPrinting, Three-DimensionalAnimalsMiceNIH 3T3 CellsBiocompatible MaterialsGelatinTissue EngineeringBioprintingEthanolaminesPhotochemical ProcessesMethylene BlueMethacrylatesRed Light

Stichwörter der Autor:innen

3D printingcolorlessgelatine methacrylate (GelMA)hydrogelsmethylene bluephotopolymerizationred light

Substanzen

HydrogelstriethanolamineBiocompatible MaterialsGelatinEthanolaminesMethylene BlueMethacrylates

Autor:innen und Institutionen

  • Faculty of Engineering and Natural Sciences, Tampere University, Tampere, 33720, Finland.
  • Drug Research Program, Faculty of Pharmacy, University of Helsinki, Helsinki, 00014, Finland.
  • Soft Matter Chemistry, Department of Chemistry, Faculty of Science, University of Helsinki, Helsinki, PB55, Finland.
  • Biomaterials and Tissue Engineering Group, Faculty of Medicine and Health Technology, Tampere University, Tampere, 33720, Finland.
  • School of Natural and Environmental Sciences, Newcastle University, Newcastle-upon-Tyne, NE1 7RU, UK.
  • New Materials and Processes Group, Faculty of Engineering, Turku University of Applied Sciences, Turku, 20520, Finland.

ORCID-Profile: Nikita Durandin

Förderung

  • Academy of Finland
  • SUSBIO PROFI7
  • H2020 European Research Council
  • Tekes
  • Luonnontieteiden ja Tekniikan Tutkimuksen Toimikunta

Zitieren

APA

Eftekhari, A., de Graaf, K. R., Takmakova, E., Jongprasitkul, H., Efimov, A., Turunen, S., Kerr, A., Kellomäki, M., Luxenhofer, R., Laaksonen, T., & Durandin, N. (2025). Traceless Photopolymerization with Non‐Pulsed Red Light Enables 3D‐Printable Cell‐Laden Hydrogels. Advanced Materials. https://doi.org/10.1002/adma.202502386

Vancouver

Eftekhari A, de Graaf KR, Takmakova E, Jongprasitkul H, Efimov A, Turunen S, et al. Traceless Photopolymerization with Non‐Pulsed Red Light Enables 3D‐Printable Cell‐Laden Hydrogels. Advanced Materials. 2025. doi:10.1002/adma.202502386

BibTeX
@article{Eftekhari2025,
  author = {Eftekhari, Ali and de Graaf, Kelsey Rianne and Takmakova, Ekaterina and Jongprasitkul, Hatai and Efimov, Alexander and Turunen, Sanna and Kerr, Andrew and Kellomäki, Minna and Luxenhofer, Robert and Laaksonen, Timo and Durandin, Nikita},
  title = {Traceless Photopolymerization with Non‐Pulsed Red Light Enables 3D‐Printable Cell‐Laden Hydrogels},
  journal = {Advanced Materials},
  year = {2025},
  doi = {10.1002/adma.202502386}
}
Kostenlos starten →