EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

High Power Density Ag 2 Se/Sb 1.5 Bi 0.5 Te 3 ‐Based Fully Printed Origami Thermoelectric Module for Low‐Grade Thermal Energy Harvesting

Leonard Franke, Andres Georg Rösch, Muhammad Irfan Khan, Qihao Zhang, Zhongmin Long, Irene Brunetti, Matías Nicolas Joglar, Ana Moya Lara, Claudia Delgado Simão, Holger Geßwein, Alexei Nefedov, Yolita M. Eggeler und 2 weitere

Advanced Functional Materials · 2024-10 · 34 (40)

DOI: 10.1002/adfm.202403646 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Advanced Functional Materials, online erschienen am 16.06.2024. Verfasst von Leonard Franke und 13 weiteren Autor:innen. Die Arbeit wurde bisher 27-mal zitiert (Crossref) und nennt 39 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Bundesministerium für Bildung und Forschung, Deutsche Forschungsgemeinschaft, Deutsche Bundesstiftung Umwelt.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Printing technologies have the potential to reduce the manufacturing costs of many electronic devices significantly. Here, a scalable manufacturing route for high‐performance fully printed thermoelectric generators (TEGs) as a cost‐effective solution for energy harvesting is demonstrated. This work presents a facile one‐pot synthesis method to develop a high‐performance Ag 2 Se‐based n‐type paste, which is used to fabricate a fully printed origami TEG by employing the Ag 2 Se‐based material for the n‐type legs and a previously reported Bi‐Sb‐Te‐based paste for the p‐type legs. The n‐type film exhibits a power factor of 13.5 µW cm −1 K −2 and a maximum figure‐of‐merit (ZT) of ≈ 0.92. Furthermore, printable carbon paste is introduced as an effective interface between the thermoelectric and electrode materials, which reduces the contact resistances in the thermoelectric device. The origami folded TEG exhibits an open‐circuit voltage (V OC ) of 284 mV, a power output of 370.88 µW, and an exceptionally high power density (p max ) of 10.72 Wm −2 at a temperature difference (∆T) of 80.7 K, considering that the TEG fabrication does not involve any pressure treatment and vacuum sintering. These results underscore the scalability of the presented manufacturing process and the capability of printed origami TEGs for powering the Internet of Things (IoT) with low‐grade waste heat.

Förderung

  • Bundesministerium für Bildung und Forschung
  • Deutsche Forschungsgemeinschaft
  • Deutsche Bundesstiftung Umwelt
  • H2020 European Research Council
  • Horizon 2020 Framework Programme
  • Ministerium für Wissenschaft, Forschung und Kunst Baden-Württemberg

Zitieren

APA

Franke, L., Rösch, A. G., Khan, M. I., Zhang, Q., Long, Z., Brunetti, I., Joglar, M. N., Lara, A. M., Simão, C. D., Geßwein, H., Nefedov, A., Eggeler, Y. M., Lemmer, U., & Mallick, M. M. (2024). High Power Density Ag 2 Se/Sb 1.5 Bi 0.5 Te 3 ‐Based Fully Printed Origami Thermoelectric Module for Low‐Grade Thermal Energy Harvesting. Advanced Functional Materials, 34(40). https://doi.org/10.1002/adfm.202403646

Vancouver

Franke L, Rösch AG, Khan MI, Zhang Q, Long Z, Brunetti I, et al. High Power Density Ag 2 Se/Sb 1.5 Bi 0.5 Te 3 ‐Based Fully Printed Origami Thermoelectric Module for Low‐Grade Thermal Energy Harvesting. Advanced Functional Materials. 2024;34(40). doi:10.1002/adfm.202403646

BibTeX
@article{Franke2024,
  author = {Franke, Leonard and Rösch, Andres Georg and Khan, Muhammad Irfan and Zhang, Qihao and Long, Zhongmin and Brunetti, Irene and Joglar, Matías Nicolas and Lara, Ana Moya and Simão, Claudia Delgado and Geßwein, Holger and Nefedov, Alexei and Eggeler, Yolita M. and Lemmer, Uli and Mallick, Md Mofasser},
  title = {High Power Density Ag 2 Se/Sb 1.5 Bi 0.5 Te 3 ‐Based Fully Printed Origami Thermoelectric Module for Low‐Grade Thermal Energy Harvesting},
  journal = {Advanced Functional Materials},
  year = {2024},
  volume = {34},
  number = {40},
  doi = {10.1002/adfm.202403646}
}
Kostenlos starten →