Boosting Piezoelectricity by 3D Printing PVDF‐MoS 2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor
Advanced Functional Materials · 2023-10 · 33 (42)
DOI: 10.1002/adfm.202302946 ↗Kurz gefasst
Fachartikel in der Zeitschrift Advanced Functional Materials, online erschienen am 21.06.2023. Verfasst von Md. Nurul Islam und 10 weiteren Autor:innen. Die Arbeit wurde bisher 172-mal zitiert (Crossref) und nennt 44 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0). Gefördert von: U.S. Department of Energy, University of North Texas.
Abstract (Originalsprache)
Additively manufactured flexible and high‐performance piezoelectric devices are highly desirable for sensing and energy harvesting of 3D conformal structures. Herein, the study reports a significantly enhanced piezoelectricity in polyvinylidene fluoride (PVDF) achieved through the in situ dipole alignment of PVDF within PVDF‐2D molybdenum disulfide (2D MoS 2 ) composite by 3D printing. The shear stress‐induced dipole poling of PVDF and 2D MoS 2 alignment are harnessed during 3D printing to boost piezoelectricity without requiring a post‐poling process. The results show a remarkable, more than the eight‐fold increment in the piezoelectric coefficient ( d 33 ) for 3D printed PVDF‐8wt.% MoS 2 composite over cast neat PVDF. The underlying mechanism of piezoelectric property enhancement is attributed to the increased volume fraction of β phase in PVDF, filler fraction, heterogeneous strain distribution around PVDF‐MoS 2 interfaces, and strain transfer to the nanofillers as confirmed by microstructural analysis and finite element simulation. These results provide a promising route to design and fabricate high‐performance 3D piezoelectric devices via 3D printing for next‐generation sensors and mechanical–electronic conformal devices.
Förderung
- U.S. Department of Energy
- University of North Texas
Zitieren
APA
Islam, M. N., Rupom, R. H., Adhikari, P. R., Demchuk, Z., Popov, I., Sokolov, A. P., Wu, H. F., Advincula, R. C., Dahotre, N., Jiang, Y., & Choi, W. (2023). Boosting Piezoelectricity by 3D Printing PVDF‐MoS 2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor. Advanced Functional Materials, 33(42). https://doi.org/10.1002/adfm.202302946
Vancouver
Islam MN, Rupom RH, Adhikari PR, Demchuk Z, Popov I, Sokolov AP, et al. Boosting Piezoelectricity by 3D Printing PVDF‐MoS 2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor. Advanced Functional Materials. 2023;33(42). doi:10.1002/adfm.202302946
BibTeX
@article{Islam2023,
author = {Islam, Md. Nurul and Rupom, Rifat Hasan and Adhikari, Pashupati R. and Demchuk, Zoriana and Popov, Ivan and Sokolov, Alexei P. and Wu, H. Felix and Advincula, Rigoberto C. and Dahotre, Narendra and Jiang, Yijie and Choi, Wonbong},
title = {Boosting Piezoelectricity by 3D Printing PVDF‐MoS 2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor},
journal = {Advanced Functional Materials},
year = {2023},
volume = {33},
number = {42},
doi = {10.1002/adfm.202302946}
}
EUVIMED