Open-source software library for real-time inertial measurement unit data-based inverse kinematics using OpenSim
PeerJ · 2023
DOI: 10.7717/peerj.15097 ↗Kurz gefasst
Fachartikel in der Zeitschrift PeerJ, 2023. Verfasst von Jere Lavikainen und 3 weiteren Autor:innen. Beteiligte Einrichtung: Department of Technical Physics, University of Eastern Finland, Kuopio, Finland. Hauptthemen laut MEDLINE: Software, Walking. Die Arbeit wurde bisher 9-mal zitiert (Crossref) und nennt 27 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0). Gefördert von: European Union, University of Eastern Finland, Digital Technology RDI Environment.
Abstract (Originalsprache)
Background
Inertial measurements (IMUs) facilitate the measurement of human motion outside the motion laboratory. A commonly used open-source software for musculoskeletal simulation and analysis of human motion, OpenSim, includes a tool to enable kinematics analysis of IMU data. However, it only enables offline analysis, i.e ., analysis after the data has been collected. Extending OpenSim’s functionality to allow real-time kinematics analysis would allow real-time feedback for the subject during the measurement session and has uses in e.g ., rehabilitation, robotics, and ergonomics.
Methods
We developed an open-source software library for real-time inverse kinematics (IK) analysis of IMU data using OpenSim. The software library reads data from IMUs and uses multithreading for concurrent calculation of IK. Its operation delays and throughputs were measured with a varying number of IMUs and parallel computing IK threads using two different musculoskeletal models, one a lower-body and torso model and the other a full-body model. We published the code under an open-source license on GitHub.
Results
A standard desktop computer calculated full-body inverse kinematics from treadmill walking at 1.5 m/s with data from 12 IMUs in real-time with a mean delay below 55 ms and reached a throughput of more than 90 samples per second. A laptop computer had similar delays and reached a throughput above 60 samples per second with treadmill walking. Minimal walking kinematics, motion of lower extremities and torso, were calculated from treadmill walking data in real-time with a throughput of 130 samples per second on the laptop and 180 samples per second on the desktop computer, with approximately half the delay of full-body kinematics.
Conclusions
The software library enabled real-time inverse kinematical analysis with different numbers of IMUs and customizable musculoskeletal models. The performance results show that subject-specific full-body motion analysis is feasible in real-time, while a laptop computer and IMUs allowed the use of the method outside the motion laboratory.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Technical Physics, University of Eastern Finland, Kuopio, Finland.
ORCID-Profile: Jere Lavikainen
Förderung
- European Union
- University of Eastern Finland
- Digital Technology RDI Environment
- Academy of Finland
Zitieren
APA
Lavikainen, J., Vartiainen, P., Stenroth, L., & Karjalainen, P. A. (2023). Open-source software library for real-time inertial measurement unit data-based inverse kinematics using OpenSim. PeerJ. https://doi.org/10.7717/peerj.15097
Vancouver
Lavikainen J, Vartiainen P, Stenroth L, Karjalainen PA. Open-source software library for real-time inertial measurement unit data-based inverse kinematics using OpenSim. PeerJ. 2023. doi:10.7717/peerj.15097
BibTeX
@article{Lavikainen2023,
author = {Lavikainen, Jere and Vartiainen, Paavo and Stenroth, Lauri and Karjalainen, Pasi A},
title = {Open-source software library for real-time inertial measurement unit data-based inverse kinematics using OpenSim},
journal = {PeerJ},
year = {2023},
doi = {10.7717/peerj.15097}
}
EUVIMED