EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-SA 4.0

Failure Analysis of a Rear-Sprocket Mounting (Nap Gear) Bolt in a 145 cc Motorcycle

Ambo Ardy Pranowo, Andiyanto Andiyanto, Ruben Sanilo, Hammam Abdirrazzaq Ats Tsaqif

Multidisciplinary Innovations and Research in Applied Engineering · 30.06.2026 · 3 (1) · 25-36

DOI: 10.70935/mdt14h15 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Multidisciplinary Innovations and Research in Applied Engineering, online erschienen am 30.06.2026. Verfasst von Ambo Ardy Pranowo und 3 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-SA 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Rear-sprocket mounting bolts, referred to in this study as nap gear bolts, transmit torque from the rear sprocket assembly to the wheel hub through the damper/bushing interface and may experience repeated transverse shear and bending loads. This study investigates the fracture of a rear-sprocket mounting (nap gear) bolt from a 145 cc motorcycle to determine its material characteristics, fracture mechanism, and mechanical cause of failure. The investigation combined macro-fractographic observation, spark-emission chemical composition testing, optical metallography, Vickers microhardness testing, and finite element analysis of a three-dimensional bolt model. The measured chemistry was consistent with the SAE 1015 low-carbon steel composition range, with 0.137 wt.% C and a ferrite-pearlite microstructure; however, the grade designation is reported as a chemical-consistency assessment rather than a mill-certified material identification. No abnormal microstructural difference or surface-hardening layer was observed between the failed and intact bolts. The hardness values were 179-190 HV0.5 for the failed bolt and 169-183 HV0.5 for the intact bolt. Fractography identified a proposed crack-initiation region, a crack-propagation region with beachmark-like macroscopic features, and a final-fracture region. Finite element analysis predicted a local maximum stress intensity, defined as the difference between the maximum and minimum principal stresses, of 529.6 MPa at the fracture location; the corresponding maximum shear stress was 264.8 MPa. The failure is therefore attributed to fatigue initiated at a stress-concentrated region, while the available evidence does not indicate that material selection or gross metallurgical abnormality was the primary cause.

Zitieren

APA

Pranowo, A. A., Andiyanto, A., Sanilo, R., & Tsaqif, H. A. A. (2026). Failure Analysis of a Rear-Sprocket Mounting (Nap Gear) Bolt in a 145 cc Motorcycle. Multidisciplinary Innovations and Research in Applied Engineering, 3(1), 25-36. https://doi.org/10.70935/mdt14h15

Vancouver

Pranowo AA, Andiyanto A, Sanilo R, Tsaqif HAA. Failure Analysis of a Rear-Sprocket Mounting (Nap Gear) Bolt in a 145 cc Motorcycle. Multidisciplinary Innovations and Research in Applied Engineering. 2026;3(1):25-36. doi:10.70935/mdt14h15

BibTeX
@article{Pranowo2026,
  author = {Pranowo, Ambo Ardy and Andiyanto, Andiyanto and Sanilo, Ruben and Tsaqif, Hammam Abdirrazzaq Ats},
  title = {Failure Analysis of a Rear-Sprocket Mounting (Nap Gear) Bolt in a 145 cc Motorcycle},
  journal = {Multidisciplinary Innovations and Research in Applied Engineering},
  year = {2026},
  volume = {3},
  number = {1},
  pages = {25--36},
  doi = {10.70935/mdt14h15}
}
Kostenlos starten →