EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Evaluation of Natural Aggregate Performance for Strength-Optimized Concrete without Chemical Admixtures

Bunyamin Bunyamin, Heru Pramanda, Muhajjir Muhajjir

Smart and Green Materials · 10.08.2026 · 3 (1) · 36-53

DOI: 10.70028/sgm.v3i1.122 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Smart and Green Materials, online erschienen am 10.08.2026. Verfasst von Bunyamin Bunyamin und 2 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Concrete is one of the most widely used construction materials due to the availability of its constituent materials and its ability to withstand structural loads. Aggregate characteristics play a crucial role in determining concrete performance, and natural aggregates continue to be the primary source of aggregate in concrete production. However, their capability to achieve the desired compressive strength without the use of chemical admixtures requires further investigation. This study aimed to evaluate the ability of natural aggregates to produce concrete with target compressive strengths of 17, 20, 23, and 26 MPa and to examine changes in the water–cement ratio (W/C) resulting from additional mixing water. The target compressive strengths were selected to represent commonly used normal-strength concrete grades for general construction. An experimental program was conducted using concrete mixtures designed for specified compressive strengths of 24, 27, 30, and 33 MPa. The target slump was set at 75–100 mm without incorporating chemical admixtures; therefore, workability was adjusted by increasing the mixing water content by approximately 7–13% of the initial design requirement. Five specimens were prepared and tested for each concrete mixture to evaluate compressive strength. The results showed that the achieved slump values ranged from 75 to 80 mm, while the corresponding compressive strengths reached 19.85, 22.74, 25.16, and 28.74 MPa, respectively. The addition of water increased the W/C ratio from 0.62 to 0.69, from 0.58 to 0.65, from 0.54 to 0.61, and from 0.49 to 0.56, representing increases of approximately 10.14–12.50%. Despite the increase in W/C ratio, the compressive strengths obtained exceeded the target values in all mixture variations. These findings indicate that natural aggregates possess sufficient quality to produce concrete with compressive strengths surpassing the specified targets, even without the use of chemical admixtures. The natural aggregates used in this study were natural river aggregates obtained from Jantho, Aceh Besar Regency, Indonesia. The investigation covered normal-strength concrete with target compressive strengths of 17, 20, 23, and 26 MPa. Statistical significance testing was not performed; however, all measured compressive strengths consistently exceeded the specified target strengths and remained within the expected acceptance margin of the adopted mix-design approach.

Zitieren

APA

Bunyamin, B., Pramanda, H., & Muhajjir, M. (2026). Evaluation of Natural Aggregate Performance for Strength-Optimized Concrete without Chemical Admixtures. Smart and Green Materials, 3(1), 36-53. https://doi.org/10.70028/sgm.v3i1.122

Vancouver

Bunyamin B, Pramanda H, Muhajjir M. Evaluation of Natural Aggregate Performance for Strength-Optimized Concrete without Chemical Admixtures. Smart and Green Materials. 2026;3(1):36-53. doi:10.70028/sgm.v3i1.122

BibTeX
@article{Bunyamin2026,
  author = {Bunyamin, Bunyamin and Pramanda, Heru and Muhajjir, Muhajjir},
  title = {Evaluation of Natural Aggregate Performance for Strength-Optimized Concrete without Chemical Admixtures},
  journal = {Smart and Green Materials},
  year = {2026},
  volume = {3},
  number = {1},
  pages = {36--53},
  doi = {10.70028/sgm.v3i1.122}
}
Kostenlos starten →