EUVIMEDEUVIMED entdecken
Crossref

Enhancing printability of 3D printable mortars using quaternary blended binders

Sanjeet Kumar Mishra, B. B Das, Rajasekaran Chandrasekaran, Salim Barbhuiya

Indian Concrete Journal · 2026 · 100 (09) · 41-52

DOI: 10.65302/icj.2026.100094 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Indian Concrete Journal, 2026. Verfasst von Sanjeet Kumar Mishra und 3 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study developed extrusion-based, 3D-printable cementitious mortars using ordinary Portland cement (OPC), fly ash (FA), ultra-fine fly ash (UFFA), and colloidal nano-silica (CNS) in binary, ternary, and quaternary binder systems for digital construction. Mix proportions were designed using EMMA software, based on the modified Andreasen and Andersen particle packing model (q = 0.26), to improve particle-size distribution and packing density. Packing efficiency was further validated through bulk density measurements and void analysis, in which the quaternary mix exhibited the lowest void content (33.2 %) and the highest packing correlation (R² = 0.996). All mixes were designed with a constant aggregate-to-binder ratio of 2. Printability performance was evaluated using a three-axis gantry-based extrusion printer equipped with a screw extruder and a 30 mm circular nozzle with a layer height of 15 mm. Key parameters assessed included flowability, flow retention, extrudability, shape retention, buildability, and open time, as well as rheological yield stress, determined via a slug test. A pre-printing structural stability test was further evaluated using a cylinder stability test simulating a layer-loading condition, with early-age strain behavior used to define buildability limits. The control mix exhibited flow retention, shape retention factor, and yield stress of 91.2 %, 0.62, and 0.647 kPa, respectively. Mix O75F25 showed high flow retention (94.2 %) but a low shape retention factor (0.6) due to low yield stress (0.617 kPa). Incorporation of ultra-fine fly ash (mix O90U10) showed a 15 % improvement in shape retention and a 12.96 % increase in yield stress compared to mix O75F25. The ternary mix (O65F20U15) surpassed the control and binary mixes in flow and shape retention, achieving 94.7 % and 0.75, respectively. The quaternary mix (O65F20U14NS1) exhibited the highest yield stress (0.832 kPa), superior shape retention (0.85), and successful printing of 15 layers after 10 minutes of mixing. This mix also recorded the lowest early-age strain (≈6.5 %), indicating enhanced green strength and structural stability. However, it had a shorter open time (90 min) compared to other mixes. Overall, improved particle packing, reduced voids, increased yield stress and lowered strain collectively enhance buildability and layer stability in the quaternary mix O65F20U14NS1, indicating strong potential for extrusion-based digital construction.

Zitieren

APA

Mishra, S. K., Das, B. B., Chandrasekaran, R., & Barbhuiya, S. (2026). Enhancing printability of 3D printable mortars using quaternary blended binders. Indian Concrete Journal, 100(09), 41-52. https://doi.org/10.65302/icj.2026.100094

Vancouver

Mishra SK, Das BB, Chandrasekaran R, Barbhuiya S. Enhancing printability of 3D printable mortars using quaternary blended binders. Indian Concrete Journal. 2026;100(09):41-52. doi:10.65302/icj.2026.100094

BibTeX
@article{Mishra2026,
  author = {Mishra, Sanjeet Kumar and Das, B. B and Chandrasekaran, Rajasekaran and Barbhuiya, Salim},
  title = {Enhancing printability of 3D printable mortars using quaternary blended binders},
  journal = {Indian Concrete Journal},
  year = {2026},
  volume = {100},
  number = {09},
  pages = {41--52},
  doi = {10.65302/icj.2026.100094}
}
Kostenlos starten →