IOT BASED WATER PUMP MONITORING & CONTROL SYSTEM
International Journal of AI Electrical Civil and Mechanical engineering · 17.11.2026 · 2 (4) · 185-192
DOI: 10.64751/wmyecf98 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of AI Electrical Civil and Mechanical engineering, online erschienen am 17.11.2026. Verfasst von Dr. N. Madhukar Reddy und 4 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
Electric water pumps are used everywhere, from domestic overhead tank filling to agricultural borewells and small municipal supply schemes. In most of these installations the pump is switched manually or through a simple float switch, and the motor has only a fuse or a basic starter for protection. As a result, tanks overflow, pumps run dry when the source level falls, and motors burn out because of low voltage, single phasing, or overload, often in locations where no operator is present. This paper presents an IoT Based Water Pump Monitoring and Control System that automates pump operation, protects the motor against common electrical and hydraulic faults, and allows remote supervision through a mobile application. The system uses an ESP32 microcontroller as the main controller. Water levels in the overhead tank and the sump or source are measured with ultrasonic and float sensors, flow in the delivery pipe is measured with a Hall effect flow sensor, and the electrical condition of the motor is measured through ZMPT101B voltage sensors on each phase and ACS712 or current transformer based sensing of motor current. A DS18B20 sensor on the motor body records winding temperature. The pump is started and stopped through a relay that drives the contactor coil of the existing direct-on-line or star-delta starter, so the high power switching remains with standard switchgear. The controller starts the pump when the tank level falls below a lower limit and stops it when the upper limit is reached, provided the source has enough water and the supply is healthy. Protection functions include dry-run detection from low current combined with zero flow, over-voltage and under-voltage trip, single phasing and phase imbalance detection, overload trip with an inverse time delay, locked rotor detection at start, and thermal trip on high motor temperature. Each trip is followed by an automatic restart attempt after a cooling interval, with a limit on the number of restarts. Operating data such as tank level, flow rate, supply voltage, motor current, power, running hours, and energy is sent over Wi-Fi to a cloud platform using MQTT, with a GSM module used as a fallback in rural areas without broadband. A dashboard and mobile application display live status, allow the user to switch the pump remotely or set a schedule, and deliver alerts for faults, overflow, and low source level. Pumping history helps estimate water delivered and energy consumed per day. This record also shows the owner how the supply voltage and the pump current vary over the day. A prototype was built with a 0.5 HP single-phase pump for testing and a simulated three-phase supply board for fault studies. The system maintained the tank level between the set limits without overflow, detected dry-run within about five seconds, and tripped on single phasing and under-voltage within the programmed delay. The results show that a low-cost IoT controller can make pumping safer, save water and energy, and reduce motor failures.
Zitieren
APA
Reddy, D. N. M., Varshitha, K., Anitha, M., Shekhar, K., & Teja, V. S. (2026). IOT BASED WATER PUMP MONITORING & CONTROL SYSTEM. International Journal of AI Electrical Civil and Mechanical engineering, 2(4), 185-192. https://doi.org/10.64751/wmyecf98
Vancouver
Reddy DNM, Varshitha K, Anitha M, Shekhar K, Teja VS. IOT BASED WATER PUMP MONITORING & CONTROL SYSTEM. International Journal of AI Electrical Civil and Mechanical engineering. 2026;2(4):185-192. doi:10.64751/wmyecf98
BibTeX
@article{Reddy2026,
author = {Reddy, Dr. N. Madhukar and Varshitha, K. and Anitha, M. and Shekhar, K. and Teja, V. Sai},
title = {IOT BASED WATER PUMP MONITORING & CONTROL SYSTEM},
journal = {International Journal of AI Electrical Civil and Mechanical engineering},
year = {2026},
volume = {2},
number = {4},
pages = {185--192},
doi = {10.64751/wmyecf98}
}
EUVIMED