EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

AUTOMOTIVE INTAKE MANIFOLD

Mr. T. Sitaram Babu, CH.Lingam, N.Harshith, MD.Rasheed pasha, P.Bala Krishna

International Journal of AI Electrical Civil and Mechanical engineering · 17.11.2026 · 2 (4) · 144-151

DOI: 10.64751/h3gqws50 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of AI Electrical Civil and Mechanical engineering, online erschienen am 17.11.2026. Verfasst von Mr. T. Sitaram Babu und 4 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The intake manifold of a spark-ignition engine carries the air that passes the throttle body to the individual cylinders. Its geometry decides how much air each cylinder receives, how much pressure is lost on the way, and how evenly the charge is shared between cylinders. A manifold that feeds one cylinder better than another causes unequal air-fuel ratios, uneven combustion and a loss of power, while a high pressure drop reduces the volumetric efficiency of the engine. This project studies the design of an intake manifold for a four-cylinder, 1.2 litre, naturally aspirated petrol engine using computer-aided design and computational fluid dynamics. The manifold was modelled in SolidWorks as a parametric assembly of a throttle inlet, a plenum and four runners, so that the plenum volume, runner diameter, runner taper and entry shape could be changed from a small set of dimensions. Three design variants were prepared from this model. The baseline variant has a 1.2 litre plenum with straight runners of 32 mm diameter. The second variant keeps the same plenum but uses runners that taper from 36 mm at the plenum to 30 mm at the port. The third variant combines the tapered runners with a larger 1.8 litre plenum and bellmouth entries at the runner inlets. The internal air volume of each variant was extracted and analysed in ANSYS Fluent as a steady, incompressible-corrected turbulent flow using the k-omega SST model. A mass-flow inlet of 0.058 kg/s, corresponding to the engine at about 5500 rpm, was applied at the throttle face, and the four runner exits were set as pressure outlets. A mesh independence study fixed the mesh at about 1.86 million poly-hexcore cells with inflation layers on the walls. Velocity contours, pressure contours, streamlines, the mass flow through each runner, the total pressure drop and a volumetric efficiency index were compared for the three variants. The baseline manifold showed a maximum runner flow deviation of 7.6 percent from the mean, with runner 1 nearest the throttle receiving the most air, and a pressure drop of 3.42 kPa. Tapered runners reduced the deviation to 3.4 percent and the pressure drop to 2.86 kPa. The third variant gave the most uniform distribution, with a maximum deviation of 1.4 percent, a pressure drop of 2.41 kPa and a volumetric efficiency index of 0.903 against 0.874 for the baseline, a relative gain of 3.3 percent. A static structural check of the selected design in glass-filled nylon under a 0.3 MPa backfire pressure at 120 degrees Celsius gave a factor of safety of 4.2.

Zitieren

APA

Babu, M. T. S., CH.Lingam, N.Harshith, pasha, M., & Krishna, P. (2026). AUTOMOTIVE INTAKE MANIFOLD. International Journal of AI Electrical Civil and Mechanical engineering, 2(4), 144-151. https://doi.org/10.64751/h3gqws50

Vancouver

Babu MTS, CH.Lingam, N.Harshith, pasha M, Krishna P. AUTOMOTIVE INTAKE MANIFOLD. International Journal of AI Electrical Civil and Mechanical engineering. 2026;2(4):144-151. doi:10.64751/h3gqws50

BibTeX
@article{Babu2026,
  author = {Babu, Mr. T. Sitaram and CH.Lingam and N.Harshith and pasha, MD.Rasheed and Krishna, P.Bala},
  title = {AUTOMOTIVE INTAKE MANIFOLD},
  journal = {International Journal of AI Electrical Civil and Mechanical engineering},
  year = {2026},
  volume = {2},
  number = {4},
  pages = {144--151},
  doi = {10.64751/h3gqws50}
}
Kostenlos starten →