AUTOMOTIVE SUSPENSION CONTROL ARM
International Journal of AI Electrical Civil and Mechanical engineering · 17.11.2026 · 2 (4) · 119-126
DOI: 10.64751/as8hc696 ↗Kurz gefasst
Fachartikel in der Zeitschrift International Journal of AI Electrical Civil and Mechanical engineering, online erschienen am 17.11.2026. Verfasst von Mr. S. Venkat Lakshman und 5 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
The lower control arm is one of the most heavily loaded members of a passenger car suspension. It connects the wheel knuckle to the vehicle body through a ball joint at the outer end and two rubber bushings at the inner end, and it carries the longitudinal, lateral and part of the vertical forces generated at the tyre contact patch during braking, cornering and travel over uneven roads. A failure of this component leads to a sudden loss of wheel control, so its strength, stiffness and fatigue behaviour must be established with care before it is manufactured. At the same time, the arm is part of the unsprung mass of the vehicle, and any reduction in its weight improves ride comfort, road holding and fuel economy. This work presents the design and analysis of a front lower control arm for a MacPherson strut suspension of a compact passenger car with a kerb mass of about 1,200 kg. The geometry of the arm was modelled in SolidWorks using hard points taken from a typical front suspension layout, and the model was transferred to ANSYS Workbench for static structural, modal and fatigue analysis. Three load cases were studied, namely braking, cornering and a combined pothole event, and the combined pothole case with 6.5 kN longitudinal, 5.8 kN lateral and 3.5 kN vertical force at the ball joint was found to govern the design. Five candidate materials were compared under identical geometry, mesh and boundary conditions: structural steel, forged alloy steel AISI 4340, aluminium alloy 6061-T6, aluminium alloy 7075-T6 and titanium alloy Ti-6Al-4V. For each material the equivalent von Mises stress, total deformation, factor of safety based on yield strength, mass and first natural frequency were recorded. Structural steel reached a maximum stress of 186.4 MPa with a factor of safety of only 1.34, while aluminium 7075-T6 reached 182.9 MPa with a factor of safety of 2.75 at a mass of 1.22 kg against 3.42 kg for the steel arm. Based on this comparison, aluminium alloy 7075-T6 was selected, and the arm was refined by adding lightening pockets in the web and a stiffening rib along the inner edge, guided by the low-stress regions seen in the contour plots. The refined arm has a mass of 1.08 kg, a maximum von Mises stress of 211.6 MPa near the front bushing neck, a total deformation of 1.94 mm and a factor of safety of 2.38. This represents a mass reduction of 68.4 percent compared with the structural steel baseline.
Zitieren
APA
Lakshman, M. S. V., Reddy, A., ShankarReddy, S., D.Nikhil, Kumar, V., & B.Ashok (2026). AUTOMOTIVE SUSPENSION CONTROL ARM. International Journal of AI Electrical Civil and Mechanical engineering, 2(4), 119-126. https://doi.org/10.64751/as8hc696
Vancouver
Lakshman MSV, Reddy A, ShankarReddy S, D.Nikhil, Kumar V, B.Ashok. AUTOMOTIVE SUSPENSION CONTROL ARM. International Journal of AI Electrical Civil and Mechanical engineering. 2026;2(4):119-126. doi:10.64751/as8hc696
BibTeX
@article{Lakshman2026,
author = {Lakshman, Mr. S. Venkat and Reddy, A.Rishikesh and ShankarReddy, S.Shiva and D.Nikhil and Kumar, V.Sharath and B.Ashok},
title = {AUTOMOTIVE SUSPENSION CONTROL ARM},
journal = {International Journal of AI Electrical Civil and Mechanical engineering},
year = {2026},
volume = {2},
number = {4},
pages = {119--126},
doi = {10.64751/as8hc696}
}
EUVIMED