EUVIMEDEUVIMED entdecken
Crossref

Tensile Coupon Testing and Residual Stress Measurements of High-Strength Steel Built-Up I-Shaped Sections

Kara Stall, Andrea Culhane, Likun Sun, Rachel Chicchi Cross, Matthew Steiner

Engineering Journal · 2024

DOI: 10.62913/engj.v61i3.1326 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Engineering Journal, 2024. Verfasst von Kara Stall und 4 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

High strength structural steels (with yield stresses greater than 65 ksi) may have notably different material characteristics when compared to structural steels conventionally used in building construction [i.e., ASTM A992/A992M (2022) or A572/A572M Gr. 50 (2021)]. This paper presents findings from an experimental program that investigated the material characterization of ASTM A656/A656M Gr. 80 (2024) plate steel. The results obtained were compared to conventional ASTM A572/A572M Gr. 50 steel. Two types of testing were performed for this work: tensile coupon testing and residual stress testing. The tensile coupon testing was carried out for both the A656/A656M Gr. 80 and A572/A572M Gr. 50 plate material. The A656/A656M Gr. 80 plate material showed more variation between the two different plate thicknesses in both mechanical behavior and microstructure due to differences in steel production. The 0.375 in. thick plate exhibited a clear yield plateau with an ultimate/yield stress ratio similar to the Gr. 50 material. In contrast, the 0.5 in. plate did not have a yield plateau and reached lower ultimate strain. The residual stress testing was performed using a sectioning technique for one A572/A572M Gr. 50 and five A656/A656M Gr. 80 built-up sections that were fabricated from 0.5 in. and 0.375 in. plate material. Residual stresses obtained from measurements were compared to previously published predictive models. The ECCS model and BSK99 models were found to be reasonable predictors of residual stresses for all specimens except the one section fabricated from 0.5 in. thick Gr. 80 plate. When comparing the Gr. 50 and Gr. 80 specimens of the same cross-sectional geometry, the residual stresses were similar, implying that cross-sectional geometry is more prevalent than the nominal yield stress in determining residual stresses in built-up I-sections.

Zitieren

APA

Stall, K., Culhane, A., Sun, L., Cross, R. C., & Steiner, M. (2024). Tensile Coupon Testing and Residual Stress Measurements of High-Strength Steel Built-Up I-Shaped Sections. Engineering Journal. https://doi.org/10.62913/engj.v61i3.1326

Vancouver

Stall K, Culhane A, Sun L, Cross RC, Steiner M. Tensile Coupon Testing and Residual Stress Measurements of High-Strength Steel Built-Up I-Shaped Sections. Engineering Journal. 2024. doi:10.62913/engj.v61i3.1326

BibTeX
@article{Stall2024,
  author = {Stall, Kara and Culhane, Andrea and Sun, Likun and Cross, Rachel Chicchi and Steiner, Matthew},
  title = {Tensile Coupon Testing and Residual Stress Measurements of High-Strength Steel Built-Up I-Shaped Sections},
  journal = {Engineering Journal},
  year = {2024},
  doi = {10.62913/engj.v61i3.1326}
}
Kostenlos starten →