Development, Implementation, and Evaluation of a Novel Low-Cost, High Anatomical Fidelity 3D-Printed Tracheostomy Care Simulation Model in Rwanda
Tracheostomy: Official Journal of the Global Tracheostomy Collaborative · 31.03.2026 · 3 (1)
DOI: 10.62905/001c.155768 ↗Kurz gefasst
Fachartikel in der Zeitschrift Tracheostomy: Official Journal of the Global Tracheostomy Collaborative, online erschienen am 31.03.2026. Verfasst von Nina Patel und 19 weiteren Autor:innen. Die Arbeit nennt 24 Literaturangaben.
Abstract (Originalsprache)
Introduction
Basic tracheostomy management is an essential skill for primary care practitioners, yet there is often limited training in formal medical education. This study aimed to develop and evaluate a low-cost, 3D-printed tracheostomy model to enhance simulation-based training and improve proficiency and confidence in airway management among general practitioners (GPs) in Rwanda, where prior research has identified gaps in training. Materials and Methods This two-phase study included expert validation by otolaryngologists followed by pilot testing of the model. Five local otolaryngologists evaluated the model’s anatomical accuracy, clinical relevance, and training utility. Subsequently, 40 GPs from across Rwanda participated in a hands-on simulation workshop in Rwanda. Training focused on suctioning, tube replacement, neck tie placement, and managing accidental decannulation. Pre- and post-training surveys assessed changes in knowledge, confidence, skill, and perceived relevance. Procedural skills were independently evaluated through standardized video and rubric assessments.
Results
Otolaryngologists rated the model highly for accuracy, relevance, and cost-effectiveness. Each reusable 3D-printed tracheostomy simulation model was produced at a cost of $32.22 USD, offering a sustainable and affordable alternative to commercial simulation tools in low-resource settings. During the training workshop, significant improvements were observed across all domains. Knowledge scores increased by 15% (p
Zitieren
APA
Patel, N., Pullakhandam, K., Cahill, G., Drapeau, S., Bukuru, J., Nteyumwete, H., Hakizimana, A., Kamaliza, A., Shaye, D. A., Nkurunziza, C., Ncogoza, I., McCall, N., Abaho, J., Nzisabira, J., Niyonkuru, D., Nishimwe, G., Uwizeyimana, E., Masimbi, O., Xu, M. J., & Tuyishimire, G. (2026). Development, Implementation, and Evaluation of a Novel Low-Cost, High Anatomical Fidelity 3D-Printed Tracheostomy Care Simulation Model in Rwanda. Tracheostomy: Official Journal of the Global Tracheostomy Collaborative, 3(1). https://doi.org/10.62905/001c.155768
Vancouver
Patel N, Pullakhandam K, Cahill G, Drapeau S, Bukuru J, Nteyumwete H, et al. Development, Implementation, and Evaluation of a Novel Low-Cost, High Anatomical Fidelity 3D-Printed Tracheostomy Care Simulation Model in Rwanda. Tracheostomy: Official Journal of the Global Tracheostomy Collaborative. 2026;3(1). doi:10.62905/001c.155768
BibTeX
@article{Patel2026,
author = {Patel, Nina and Pullakhandam, Kamala and Cahill, Gabrielle and Drapeau, Scott and Bukuru, John and Nteyumwete, Hirwa and Hakizimana, Aristote and Kamaliza, Aimee and Shaye, David A. and Nkurunziza, Charles and Ncogoza, Isaie and McCall, Natalie and Abaho, Jonathan and Nzisabira, Joselyne and Niyonkuru, Derrick and Nishimwe, Gloria and Uwizeyimana, Eric and Masimbi, Ornella and Xu, Mary Jue and Tuyishimire, Gratien},
title = {Development, Implementation, and Evaluation of a Novel Low-Cost, High Anatomical Fidelity 3D-Printed Tracheostomy Care Simulation Model in Rwanda},
journal = {Tracheostomy: Official Journal of the Global Tracheostomy Collaborative},
year = {2026},
volume = {3},
number = {1},
doi = {10.62905/001c.155768}
}
EUVIMED