EUVIMEDEUVIMED entdecken
Crossref

Preparation, Performance, and Environmental Deterioration of Cement-Based Self-Insulating Wall Materials

Xianliang Yin, Liang Zhao, Liping Tian, Xiaolong Li, Qiuwang Jiang

Journal of Civil and Transportation Engineering · 2026-09 · 3 (3) · 11-17

DOI: 10.62517/jcte.202606302 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Civil and Transportation Engineering, 2026-09. Verfasst von Xianliang Yin und 4 weiteren Autor:innen. Die Arbeit nennt 10 Literaturangaben.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

This study focuses on cement-based self-insulating wall materials, conducting experimental research on pore structure control, optimization of fundamental properties, and performance degradation under high humidity and thermal conditions. Using 42.5-grade Portland cement as the primary binder, modified sodium rosinate as the foaming agent, and waste engine oil as the foam stabilizer, cement-based self-insulating wall materials with varying water-to-cement ratios and pore sizes were prepared via physical foaming. The true density, apparent density, water absorption rate, closed-pore ratio, compressive strength, and microstructure were tested. Subsequently, a coupled high-temperature-high-humidity environment (40 °C, 80% RH) was applied to analyze the effects of temperature and humidity on the material's thermal conductivity and mechanical properties. Results indicate that both water-to-cement ratio and pore size significantly influence the pore structure and macroscopic performance. Excessively high water-to-cement ratios increase interconnected pores and visible voids, leading to higher water absorption, lower closed-pore content, and reduced material strength. Conversely, excessively large pore sizes tend to cause thinning of pore walls, pore interconnection, and structural delamination, which hinder the simultaneous improvement of insulation and mechanical performance. When the water-to-cement ratio is 0.50 and pore size ranges from 1.0 to 2.5 mm, the material exhibits optimal overall performance: a closed-pore ratio of 34.59%, water absorption of 11.30%, compressive strength of 6.15 MPa, a thermal conductivity of 0.087 W·m⁻¹·K⁻¹ in dry condition, and 0.099 W·m⁻¹·K⁻¹ after exposure to high humidity and heat—representing a degradation rate of only 13.79%. In contrast, samples with high water-to-cement ratios and large pores show significantly increased thermal conductivity under humid-heat conditions, indicating greater environmental sensitivity. The study demonstrates that an appropriate water-to-cement ratio combined with moderate pore size promotes a higher closed-pore ratio and more stable pore structure, enabling coordinated optimization of lightweight, thermal insulation, mechanical strength, and resistance to moisture-heat degradation in cement-based self-insulating wall materials.

Zitieren

APA

Yin, X., Zhao, L., Tian, L., Li, X., & Jiang, Q. (2026). Preparation, Performance, and Environmental Deterioration of Cement-Based Self-Insulating Wall Materials. Journal of Civil and Transportation Engineering, 3(3), 11-17. https://doi.org/10.62517/jcte.202606302

Vancouver

Yin X, Zhao L, Tian L, Li X, Jiang Q. Preparation, Performance, and Environmental Deterioration of Cement-Based Self-Insulating Wall Materials. Journal of Civil and Transportation Engineering. 2026;3(3):11-17. doi:10.62517/jcte.202606302

BibTeX
@article{Yin2026,
  author = {Yin, Xianliang and Zhao, Liang and Tian, Liping and Li, Xiaolong and Jiang, Qiuwang},
  title = {Preparation, Performance, and Environmental Deterioration of Cement-Based Self-Insulating Wall Materials},
  journal = {Journal of Civil and Transportation Engineering},
  year = {2026},
  volume = {3},
  number = {3},
  pages = {11--17},
  doi = {10.62517/jcte.202606302}
}
Kostenlos starten →