Real-Time Buckling Monitoring of a Thin Rod Using Shape Sensing with Distributed Fiber-Optic Sensors
e-Journal of Nondestructive Testing · 2026-08 · 31 (8)
DOI: 10.58286/34013 ↗Kurz gefasst
Fachartikel in der Zeitschrift e-Journal of Nondestructive Testing, 2026-08. Verfasst von Chongli Shen und 4 weiteren Autor:innen.
Abstract (Originalsprache)
Buckling in slender members, including rods and plates, can cause a sudden loss of load-carrying capacity and stiffness, which poses safety risks. Point sensors such as strain gauges may miss localized curvature peaks and can fail when deformation becomes large. On the other hand, distributed fiber‑optic shape sensing based on OFDR‑FBG, implemented in a stress‑free, non‑bonded configuration, enables lightweight, full‑field measurements with high spatial resolution and real‑time updates without risking sensor failure at large curvature or altering the host stiffness (Fig. 1). We present a four‑core multi‑core fiber (MCF) OFDR‑FBG shape‑sensing approach routed inside a PTFE tube and mounted non‑bonded along a thin aluminum rod. The system reconstructs the rod centerline shape in real time from distributed strain sampled at approximately 0.6 mm spacing, and it tracks the progression from pre‑buckling to post‑buckling while identifying changes in buckling mode. This capability does not rely on visual data, which is valuable when visual inspection is unavailable (e.g., underwater or in low‑light environments) and where accelerometers may not reliably resolve mode changes under complex boundary and loading conditions. Our objectives are to demonstrate real-time buckling monitoring with a four-core OFDR-FBG system, to reconstruct shape with sub-millimeter spatial sampling, to monitor post-buckling behavior, and to define possible early-warning indicators based on the maximum curvature and its growth rate. Performance is evaluated by RMS error in shape, RMS error in curvature, and repeatability across runs, using the vision-derived shape as ground truth. The current system delivers continuous distributed strain, supports real-time reconstruction, detects the onset of buckling, identifies buckling mode, and follows post-buckling deformation without sensor damage. Trends in maximum curvature and its rate increase as the instability approaches, suggesting that possible early warning is achievable once thresholds are tuned and verified. We expect to show that a stress-free, non-bonded four-core OFDR-FBG configuration can track shape in real time to provide structural health monitoring for thin structures. We further expect to conclude that real-time monitoring, mode tracking, and post-buckling analysis are feasible with high spatial resolution, even in settings where visual inspection/data are unavailable.Anticipated limitations include thermal effects and sensitivity to boundary assumptions, which we plan to mitigate through temperature referencing and calibration. These results are intended to form a foundation for future SHM of slender components and to extend to other materials and geometries.
Zitieren
APA
Shen, C., Kurokawa, H., Nakamoto, S., Kobayashi, M., & Murayama, H. (2026). Real-Time Buckling Monitoring of a Thin Rod Using Shape Sensing with Distributed Fiber-Optic Sensors. e-Journal of Nondestructive Testing, 31(8). https://doi.org/10.58286/34013
Vancouver
Shen C, Kurokawa H, Nakamoto S, Kobayashi M, Murayama H. Real-Time Buckling Monitoring of a Thin Rod Using Shape Sensing with Distributed Fiber-Optic Sensors. e-Journal of Nondestructive Testing. 2026;31(8). doi:10.58286/34013
BibTeX
@article{Shen2026,
author = {Shen, Chongli and Kurokawa, Hyuga and Nakamoto, Shintaro and Kobayashi, Makito and Murayama, Hideaki},
title = {Real-Time Buckling Monitoring of a Thin Rod Using Shape Sensing with Distributed Fiber-Optic Sensors},
journal = {e-Journal of Nondestructive Testing},
year = {2026},
volume = {31},
number = {8},
doi = {10.58286/34013}
}
EUVIMED