Investigation into the Attenuative Properties of Materials Commonly Used for Wind Turbine Blade Applications
e-Journal of Nondestructive Testing · 2026-08 · 31 (8)
DOI: 10.58286/33815 ↗Kurz gefasst
Fachartikel in der Zeitschrift e-Journal of Nondestructive Testing, 2026-08. Verfasst von Robert Lochhead und 2 weiteren Autor:innen.
Abstract (Originalsprache)
As wind energy capacity increases and moves further offshore, effective structural health monitoring of wind turbine blades (WTBs) becomes critical to mitigate turbine failures. Acoustic Emission (AE) monitoring offers a promising solution, in which piezoelectric sensors detect stress waves generated by developing defects. However, the successful deployment of AE systems requires knowledge of the material’s wave attenuation properties to accurately determine sensor coverage. Current literature provides limited data on the direction and frequency dependent attenuation of anisotropic Glass Fibre Reinforced Plastic (GFRP) composites commonly used in WTBs. This study investigates attenuation properties of unidirectional and triaxial ([0/±45]) GFRP composites that are commonly used for WTB applications. The composites used in this study are excited using 10mm diameter piezoelectric disc over the 100–500 kHz frequency range, producing Lamb waves which were measured using AE sensors positioned at five propagation angles (0° - 90°) and distances (50–200 mm) from the piezoelectric disc. Attenuation coefficients were calculated by comparing signal amplitudes across positions and frequencies, with both fundamental Lamb modes considered. The study demonstrated a strong dependency of frequency and propagation direction on AE signal attenuation. In the unidirectional composite, S0 attenuation along the 0° fibre direction increased from 2.7 to 9.9 Nepers/m between 100–500 kHz, while A0 rose from 6.8 to 16.2 Nepers/m. Off-fibre propagation (90°) produced much higher values in the region of 30.8 to 41.4 Nepers/m for the S0 and A0 mode respectively, and even a 20° misalignment caused marked increases, confirming strong anisotropy. The triaxial composite also exhibited directional-dependant attenuation, though more complex when compared to unidirectional. Attenuation along the fibre aligned directions ranged from 4.4 to 16.5 Nepers/m for S0 and from 8.9 to 21 Nepers/m for A0, with off-fibre propagation showing further increases upwards of 43.2 Nepers/m. As with the unidirectional composite, attenuation grew with frequency, and A0 consistently exceeded S0, reflecting its flexural character. To assess the practical implications for AE monitoring, the attenuation coefficients from this study were compared with typical matrix cracking source amplitudes reported in the literature (approximately 62.1 dB). Assuming an AE sensor detection threshold of 40 dB, this corresponds to an allowable amplitude loss of 22.1 dB along the propagation path. Using this threshold, the measured attenuation coefficients yield an estimated detection range of approximately 0.7m for on-fibre propagation directions, which reduced to just 0.2m when considering off-fibre propagation directions. This AE sensor detection range considers both the unidirectional and triaxial composites, broadly agrees with values reported in other experimental studies and also provides new insight into frequency and direction dependent attenuation of unidirectional and triaxial GFRP composites. In conclusion, this study demonstrates that GFRP attenuation can constrain AE coverage in WTBs, and whilst AE monitoring remains viable, effective deployment requires careful sensor placement with expected coverage distance of 0.2 – 0.7m. This approach is being extended to biaxial layups and sandwich core composites, enabling more realistic sensor network designs for industrial full-scale blades.
Zitieren
APA
Lochhead, R., Gachagan, A., & Carroll, J. (2026). Investigation into the Attenuative Properties of Materials Commonly Used for Wind Turbine Blade Applications. e-Journal of Nondestructive Testing, 31(8). https://doi.org/10.58286/33815
Vancouver
Lochhead R, Gachagan A, Carroll J. Investigation into the Attenuative Properties of Materials Commonly Used for Wind Turbine Blade Applications. e-Journal of Nondestructive Testing. 2026;31(8). doi:10.58286/33815
BibTeX
@article{Lochhead2026,
author = {Lochhead, Robert and Gachagan, Anthony and Carroll, James},
title = {Investigation into the Attenuative Properties of Materials Commonly Used for Wind Turbine Blade Applications},
journal = {e-Journal of Nondestructive Testing},
year = {2026},
volume = {31},
number = {8},
doi = {10.58286/33815}
}
EUVIMED