EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Comparative study of frictional behavior of Cr-doped and Al:Ti-doped DLC coatings on AISI 4140 steel

Nattapol PINTITRARATIBODEE, Kanokwan SAENGKIETTIYUT, Yuttanant BOONYONGMANEERAT, Da-Yung WANG, Suwin SOMPOPSART

Journal of Metals, Materials and Minerals · 18.11.2026 · 37 (1) · e2688

DOI: 10.55713/jmmm.v37i1.2688 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Metals, Materials and Minerals, online erschienen am 18.11.2026. Verfasst von Nattapol PINTITRARATIBODEE und 4 weiteren Autor:innen. Die Arbeit nennt 21 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Diamond-like carbon (DLC) coatings have attracted significant interest for applications requiring low friction and high surface durability. Consequently, various DLC formulations have been developed to meet different tribological demands. In this study, the frictional behavior of AISI 4140 carbon steel, which is a widely used high strength structural material, was investigated following surface modification with two distinct DLC coating configurations. Specifically, Cr‒doped DLC with a graded CrCN interlayer (Cr‒DLC/CrCN) and AlTi-doped DLC with a graded AlTiCN interlayer (Al:Ti‒DLC/AlTiCN) were compared. Wear tests were performed using the ball-on-flat method. The results show that the Cr‒DLC/ CrCN coating exhibited a lower coefficient of friction (0.26) than the Al:Ti‒DLC/AlTiCN coating (0.30). Laser scanning confocal microscopy also revealed a smaller wear track on the Cr‒DLC/CrCN surface, with a reduced depth (2.52 µm) and width (496.68 µm). Raman spectroscopy indicated a higher sp2 bonding fraction in the Cr‒DLC/CrCN coating, as reflected by its increased ID/IG ratio, which contributed to its lower friction behavior. Overall, the Cr‒DLC/CrCN coating demonstrated superior tribological performance and wear resistance, making it a more promising surface modification for enhancing the durability of AISI 4140 carbon steel in severe sliding wear environments, typical in oil and gas industries.

Zitieren

APA

PINTITRARATIBODEE, N., SAENGKIETTIYUT, K., BOONYONGMANEERAT, Y., WANG, D., & SOMPOPSART, S. (2026). Comparative study of frictional behavior of Cr-doped and Al:Ti-doped DLC coatings on AISI 4140 steel. Journal of Metals, Materials and Minerals, 37(1), e2688. https://doi.org/10.55713/jmmm.v37i1.2688

Vancouver

PINTITRARATIBODEE N, SAENGKIETTIYUT K, BOONYONGMANEERAT Y, WANG D, SOMPOPSART S. Comparative study of frictional behavior of Cr-doped and Al:Ti-doped DLC coatings on AISI 4140 steel. Journal of Metals, Materials and Minerals. 2026;37(1):e2688. doi:10.55713/jmmm.v37i1.2688

BibTeX
@article{PINTITRARATIBODEE2026,
  author = {PINTITRARATIBODEE, Nattapol and SAENGKIETTIYUT, Kanokwan and BOONYONGMANEERAT, Yuttanant and WANG, Da-Yung and SOMPOPSART, Suwin},
  title = {Comparative study of frictional behavior of Cr-doped and Al:Ti-doped DLC coatings on AISI 4140 steel},
  journal = {Journal of Metals, Materials and Minerals},
  year = {2026},
  volume = {37},
  number = {1},
  pages = {e2688},
  doi = {10.55713/jmmm.v37i1.2688}
}
Kostenlos starten →