EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Sustainable lightweight foams from hazardous aluminum dross

Chayapat WEERAPAKDEE, Makoto NANKO, Yen-Ling KUO, Sukasem WATCHARAMAISAKUL, Kaito SUZUKI, Seiryu SUZUKI, Siriwan CHOKKHA

Journal of Metals, Materials and Minerals · 22.06.2026 · 36 (3) · e2549

DOI: 10.55713/jmmm.v36i3.2549 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Metals, Materials and Minerals, online erschienen am 22.06.2026. Verfasst von Chayapat WEERAPAKDEE und 6 weiteren Autor:innen. Die Arbeit nennt 17 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aluminum dross is a hazardous byproduct from aluminum industry that causes environmental problems and high disposal cost. This work presents a sustainable route to upcycle secondary aluminum dross into lightweight ceramic foams for insulating refractory applications. Secondary aluminum dross powder was blended with polyethylene (PE) pore-forming agents (30 vol% to 70 vol%) and polyvinyl alcohol (PVA) binder added as a 7.5 wt% aqueous solution (binder contents: 1 vol% and 3 vol%), followed by pressing and sintering at 1400℃. Increasing PE systematically reduced bulk density and increased open porosity. At 70 vol% PE, the foams reached a bulk density of 0.94 g∙cm‒3 and open porosity of ~74%, satisfying the Japanese Industrial Standard (JIS) specification for lightweight refractory bricks. The maximum compressive strength was ~2 MPa, sufficient for thermal insulation where load-bearing capacity is secondary. X-ray diffraction confirmed a multiphase matrix of α−Al2O3, MgAl2O4, and CaAl12O19, indicating solid-state reactions between alumina and Mg/Ca-bearing phases. Morphology revealed a well-connected porous network stabilized by reaction-bonded bridges, indicating strong interparticle bonding and limited pore coalescence during sintering. This approach can divert over 1000 kg of hazardous waste per ton of secondary aluminum dross processed and cut CO2 emissions by 65% versus alumina routes. The approach promotes circular economy through waste-derived ceramics.

Zitieren

APA

WEERAPAKDEE, C., NANKO, M., KUO, Y., WATCHARAMAISAKUL, S., SUZUKI, K., SUZUKI, S., & CHOKKHA, S. (2026). Sustainable lightweight foams from hazardous aluminum dross. Journal of Metals, Materials and Minerals, 36(3), e2549. https://doi.org/10.55713/jmmm.v36i3.2549

Vancouver

WEERAPAKDEE C, NANKO M, KUO Y, WATCHARAMAISAKUL S, SUZUKI K, SUZUKI S, et al. Sustainable lightweight foams from hazardous aluminum dross. Journal of Metals, Materials and Minerals. 2026;36(3):e2549. doi:10.55713/jmmm.v36i3.2549

BibTeX
@article{WEERAPAKDEE2026,
  author = {WEERAPAKDEE, Chayapat and NANKO, Makoto and KUO, Yen-Ling and WATCHARAMAISAKUL, Sukasem and SUZUKI, Kaito and SUZUKI, Seiryu and CHOKKHA, Siriwan},
  title = {Sustainable lightweight foams from hazardous aluminum dross},
  journal = {Journal of Metals, Materials and Minerals},
  year = {2026},
  volume = {36},
  number = {3},
  pages = {e2549},
  doi = {10.55713/jmmm.v36i3.2549}
}
Kostenlos starten →