Comparison between a bulk-fill resin-based composite and three luting materials on the cementation of fiberglass-reinforced posts
Restorative Dentistry & Endodontics · 2023 · 48 (3)
DOI: 10.5395/rde.2023.48.e30 ↗Kurz gefasst
Fachartikel in der Zeitschrift Restorative Dentistry & Endodontics, 2023. Verfasst von Carlos Alberto Kenji Shimokawa und 5 weiteren Autor:innen. Beteiligte Einrichtung: Department of Restorative Dentistry, School of Dentistry, University of São Paulo, São Paulo, SP, Brazil. Die Arbeit wurde bisher 2-mal zitiert (Crossref) und nennt 31 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).
Abstract (Originalsprache)
Objectives
This study verified the possibility of cementing fiberglass-reinforced posts using a flowable bulk-fill composite (BF), comparing its push-out bond strength and microhardness with these properties of 3 luting materials. Materials and Methods: Sixty endodontically treated bovine roots were used. Posts were cemented using conventional dual-cured cement (CC); self-adhesive cement (SA); dual-cured composite (RC); and BF. Push-out bond strength (n = 10) and microhardness (n = 5) tests were performed after 1 week and 4 months of storage. Two-way repeated measures analysis of variance (ANOVA), 1-way ANOVA, t-test, and Tukey post-hoc tests were applied for the push-out bond strength and microhardness results; and Pearson correlation test was applied to verify the correlation between push-out bond strength and microhardness results (α = 0.05).
Results
BF presented higher push-out bond strength than CC and SA in the cervical third before aging (p < 0.01). No differences were found between push-out bond strength before and after aging for all the luting materials (p = 0.84). Regarding hardness, only SA presented higher values measured before than after aging (p < 0.01). RC and BF did not present 80% of the maximum hardness at the apical regions. A strong positive correlation was found between the luting materials' push-out bond strength and microhardness (p < 0.01, R2 = 0.7912).
Conclusions
The BF presented comparable or higher push-out bond strength and microhardness than the luting materials, which indicates that it could be used for cementing resin posts in situations where adequate light curing is possible.
Schlagwörter
Stichwörter der Autor:innen
Autor:innen und Institutionen
- Department of Restorative Dentistry, School of Dentistry, University of São Paulo, São Paulo, SP, Brazil.
- Centro Universitário do Estado do Pará, Belém, PA, Brazil.
- Department of Biomaterials and Oral Biology, School of Dentistry, University of São Paulo, São Paulo, SP, Brazil.
ORCID-Profile: Carlos Alberto Kenji Shimokawa, Paula Mendes Acatauassú Carneiro, Tamile Rocha da Silva Lobo, Roberto Ruggiero Braga, Míriam Lacalle Turbino, Adriana Bona Matos
Zitieren
APA
Shimokawa, C. A. K., Carneiro, P. M. A., Lobo, T. R. D. S., Braga, R. R., Turbino, M. L., & Matos, A. B. (2023). Comparison between a bulk-fill resin-based composite and three luting materials on the cementation of fiberglass-reinforced posts. Restorative Dentistry & Endodontics, 48(3). https://doi.org/10.5395/rde.2023.48.e30
Vancouver
Shimokawa CAK, Carneiro PMA, Lobo TRDS, Braga RR, Turbino ML, Matos AB. Comparison between a bulk-fill resin-based composite and three luting materials on the cementation of fiberglass-reinforced posts. Restorative Dentistry & Endodontics. 2023;48(3). doi:10.5395/rde.2023.48.e30
BibTeX
@article{Shimokawa2023,
author = {Shimokawa, Carlos Alberto Kenji and Carneiro, Paula Mendes Acatauassú and Lobo, Tamile Rocha da Silva and Braga, Roberto Ruggiero and Turbino, Míriam Lacalle and Matos, Adriana Bona},
title = {Comparison between a bulk-fill resin-based composite and three luting materials on the cementation of fiberglass-reinforced posts},
journal = {Restorative Dentistry & Endodontics},
year = {2023},
volume = {48},
number = {3},
doi = {10.5395/rde.2023.48.e30}
}
EUVIMED