EUVIMEDEUVIMED entdecken
Crossref

Design, Development and CFD Analysis of a Venturi-Type Air–Fuel Mixer for a Biogas-Operated Single-Cylinder Four-Stroke Spark-Ignition Engine

Sudhir M. Arali

Dandao Xuebao/Journal of Ballistics · 22.06.2026 · 38 (2) · 1000-1019

DOI: 10.52783/dxjb.v38.443 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Dandao Xuebao/Journal of Ballistics, online erschienen am 22.06.2026. Verfasst von Sudhir M. Arali.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Biogas is a renewable, widely producible and carbon-neutral fuel whose adoption in spark-ignition (SI) engines is limited less by its combustion chemistry than by the absence of an induction device able to meter and homogenize a low-density, carbon-dioxide-diluted gaseous fuel. Conventional float-chamber carburettors are designed for liquid fuels and cannot supply a controlled stoichiometric mixture of gaseous biogas; a dedicated, low-cost mixing device is therefore the most practical route to converting existing small engines to biogas. This paper presents the complete analytical design, CAD modelling, computational-fluid-dynamics (CFD) analysis, validation and additive-manufacturing realization of a venturi-type air–fuel mixer for a 100 cm³ single-cylinder four-stroke SI engine (Hero Honda Splendor). A sixteen-step Bernoulli-based design procedure was used to size the venturi over a parametric matrix of three throat diameters (14.23, 16.92 and 18.84 mm, corresponding to convergence angles of 25°, 20° and 15°) and one to three throat gas ports, across the engine speed range of 1000–8000 rev/min. The candidate geometries were modelled in CATIA and analyzed in ANSYS CFX for pressure, velocity, phase volume fraction and turbulent kinetic energy, and a spring-loaded slider-and-needle mechanism was designed to schedule the air and gas flow areas with throttle. The novelty of the work lies in (i) a fully parametric, equation-driven venturi design that ties throat geometry directly to the biogas stoichiometric requirement, (ii) a CFD-validated demonstration that the 16.92 mm throat delivers an air–fuel ratio within the 10:1–15:1 biogas window while promoting throat turbulence, and (iii) a 3D-printed (fused-deposition-modelling, PLA) prototype that establishes a low-cost manufacturing path. Analytical and CFD air–fuel ratios agreed within about 5–9% across the speed range, and the device reproduced the target carburettor performance curve, confirming that a correctly dimensioned venturi mixer is a simple, cheap and effective means of enabling biogas operation of small SI engines.

Zitieren

APA

Arali, S. M. (2026). Design, Development and CFD Analysis of a Venturi-Type Air–Fuel Mixer for a Biogas-Operated Single-Cylinder Four-Stroke Spark-Ignition Engine. Dandao Xuebao/Journal of Ballistics, 38(2), 1000-1019. https://doi.org/10.52783/dxjb.v38.443

Vancouver

Arali SM. Design, Development and CFD Analysis of a Venturi-Type Air–Fuel Mixer for a Biogas-Operated Single-Cylinder Four-Stroke Spark-Ignition Engine. Dandao Xuebao/Journal of Ballistics. 2026;38(2):1000-1019. doi:10.52783/dxjb.v38.443

BibTeX
@article{Arali2026,
  author = {Arali, Sudhir M.},
  title = {Design, Development and CFD Analysis of a Venturi-Type Air–Fuel Mixer for a Biogas-Operated Single-Cylinder Four-Stroke Spark-Ignition Engine},
  journal = {Dandao Xuebao/Journal of Ballistics},
  year = {2026},
  volume = {38},
  number = {2},
  pages = {1000--1019},
  doi = {10.52783/dxjb.v38.443}
}
Kostenlos starten →