Design and Use of a 3D-Printed Dynamic Upper Extremity Orthosis for Children With Cerebral Palsy and Severe Upper Extremity Involvement: A Pilot Study
The American Journal of Occupational Therapy · 01.07.2023 · 77 (4)
DOI: 10.5014/ajot.2023.050095 ↗Kurz gefasst
Fachartikel in der Zeitschrift The American Journal of Occupational Therapy, online erschienen am 23.08.2023. Verfasst von Lori B Ragni und 7 weiteren Autor:innen. Beteiligte Einrichtung: Lori B. Ragni, MS, OTR/L, BCP, is Supervisor, Pediatric Occupational Therapy, Rusk Rehabilitation, NYU Langone Health, NYU Langone Orthopedic Hospita…. Hauptthemen laut MEDLINE: Cerebral Palsy. Die Arbeit wurde bisher 6-mal zitiert (Crossref) und nennt 40 Literaturangaben.
Themen: Kinderkrankenpflege
Abstract (Originalsprache)
Importance: Children with cerebral palsy (CP) and severe hand impairment have limited options for upper extremity (UE) orthoses.
Objective
To (1) design and fabricate a customized low-cost, functional, three-dimensional (3D) printed dynamic upper extremity orthosis (DUEO) and (2) examine, using a comprehensive evaluation, the effect of the orthosis on the UE function of children with unilateral UE CP, Manual Ability Classification System (MACS) Levels III to V.
Design
Pilot study. Assessments were performed pretreatment and immediately posttreatment.
Setting
Hospital-based outpatient occupational therapy department.
Participants
Five patients, ages 13 to 17 yr, with CP and unilateral UE involvement MACS Levels III to V.
Intervention
Custom forearm thumb opponens orthosis and the DUEO were designed and fabricated by a multidisciplinary team for use during eight 1-hr occupational therapy sessions targeting bimanual UE training. Outcomes and Measures: Pretreatment and posttreatment assessments included the Assisting Hand Assessment (AHA), Melbourne Assessment 2 (MA–2), Pediatric Motor Activity Log–Revised (PMAL–R), and the Pediatric Quality of Life Inventory: CP Module (PedsQL:CP).
Results
All participants had higher posttreatment scores on at least one measure. Four had minimal clinically important differences (MCID) on the AHA. Three met MCID criteria on MA-2 subtests (one negative change). Four demonstrated improvement on the PMAL–R (one participant achieved an MCID score), and three reported improvements in more than one PedsQL:CP domain. Conclusions and Relevance: This novel 3D-printed device, in combination with occupational therapy, shows promising evidence that children who score in lower MACS levels can show gains in UE function. What This Article Adds: This study demonstrates that a customized, 3D-printed dynamic orthosis, in combination with occupational therapy intervention, can facilitate UE function in children with severe hand impairment.
Schlagwörter
MeSH-Schlagwörter (MEDLINE)
Substanzen
Autor:innen und Institutionen
- Lori B. Ragni, MS, OTR/L, BCP, is Supervisor, Pediatric Occupational Therapy, Rusk Rehabilitation, NYU Langone Health, NYU Langone Orthopedic Hospital, New York, NY.
- Stacy Kirsch Dlugacz, MS, OTR/L, C/NDT, is Clinical Specialist, Pediatric Occupational Therapy, Rusk Rehabilitation, NYU Langone Health, NYU Langone Orthopedic Hospital, New York, NY.
- Cali Sadowsky, MS, OTR/L, is Senior Occupational Therapist, Pediatric Occupational Therapy, Rusk Rehabilitation, NYU Langone Health, NYU Langone Orthopedic Hospital, New York, NY.
- Gabriella Cammarata, MS, is Studio Research Coordinator, Tandon School of Engineering, New York University, Brooklyn, NY.
- Debra A. Sala, MS, PT, is Research Coordinator, Division of Pediatric Orthopedics, Hassenfeld Children's Hospital, NYU Langone Health, New York, NY.
- Victoria Bill, MS, is Director, MakerSpace, and Adjunct Professor, Tandon School of Engineering, New York University, Brooklyn, NY.
Zitieren
APA
Ragni, L. B., Dlugacz, S. K., Sadowsky, C., Cammarata, G., Sala, D. A., Bill, V., Sukhov, R., & Chu, A. (2023). Design and Use of a 3D-Printed Dynamic Upper Extremity Orthosis for Children With Cerebral Palsy and Severe Upper Extremity Involvement: A Pilot Study. The American Journal of Occupational Therapy, 77(4). https://doi.org/10.5014/ajot.2023.050095
Vancouver
Ragni LB, Dlugacz SK, Sadowsky C, Cammarata G, Sala DA, Bill V, et al. Design and Use of a 3D-Printed Dynamic Upper Extremity Orthosis for Children With Cerebral Palsy and Severe Upper Extremity Involvement: A Pilot Study. The American Journal of Occupational Therapy. 2023;77(4). doi:10.5014/ajot.2023.050095
BibTeX
@article{Ragni2023,
author = {Ragni, Lori B and Dlugacz, Stacy Kirsch and Sadowsky, Cali and Cammarata, Gabriella and Sala, Debra A and Bill, Victoria and Sukhov, Renat and Chu, Alice},
title = {Design and Use of a 3D-Printed Dynamic Upper Extremity Orthosis for Children With Cerebral Palsy and Severe Upper Extremity Involvement: A Pilot Study},
journal = {The American Journal of Occupational Therapy},
year = {2023},
volume = {77},
number = {4},
doi = {10.5014/ajot.2023.050095}
}
EUVIMED