EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

An Assessment of Single- and Three-Layer Wood-Plastic Composite Hole-Machining Using Abrasive Waterjet Cutting

Kunlapat Thongkaew, Thanate Ratanawilai, Luksika Peter, Zaleha Mustafa

Engineering, Technology & Applied Science Research · 04.04.2026 · 16 (2) · 33985-33992

DOI: 10.48084/etasr.16707 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Engineering, Technology & Applied Science Research, online erschienen am 04.04.2026. Verfasst von Kunlapat Thongkaew und 3 weiteren Autor:innen. Die Arbeit nennt 28 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Wood-Plastic Composites (WPCs) are commonly used in furniture and structural applications. However, forming-based fabrication limits the production of complex shapes. Therefore, post-machining operations, such as hole machining, are required for WPCs, and achieving high machining quality remains challenging owing to the unique properties and layered structures of materials. Therefore, the novelty of this study lies in assessing the machinability of Abrasive WaterJet (AWJ) cutting as an effective non-traditional machining method for hole fabrication in single-layer and three-layer WPCs, comparing its performance with WaterJet (WJ) cutting and conventional drilling. The effects of water pressure, traverse speed, abrasive mass flow rate, and hole diameter on the roundness and machined surface quality were investigated experimentally. The results show that AWJ successfully produced through-cut holes in both WPC structures, whereas pure WJ achieved complete cuts mainly at 350 MPa water pressure due to insufficient cutting energy at lower pressure to surpass the material’s hardness. According to response optimization, the proposed AWJ parameters are an abrasive mass flow rate of 6.67 g/s, a water pressure of 350 MPa, and a traverse speed of 30 mm/s, yielding a high desirability index of 0.848. A regression model was developed to predict roundness, and its validation revealed a small difference of 3.19% between the predicted and actual values. Compared to traditional hole drilling, AWJ offers shorter processing times and greater flexibility in hole size without requiring tool changes, although it results in larger hole roundness quality, which remains acceptable for clearance-fit applications. These findings highlight the potential of AWJ as an attractive option for machining WPCs.

Zitieren

APA

Thongkaew, K., Ratanawilai, T., Peter, L., & Mustafa, Z. (2026). An Assessment of Single- and Three-Layer Wood-Plastic Composite Hole-Machining Using Abrasive Waterjet Cutting. Engineering, Technology & Applied Science Research, 16(2), 33985-33992. https://doi.org/10.48084/etasr.16707

Vancouver

Thongkaew K, Ratanawilai T, Peter L, Mustafa Z. An Assessment of Single- and Three-Layer Wood-Plastic Composite Hole-Machining Using Abrasive Waterjet Cutting. Engineering, Technology & Applied Science Research. 2026;16(2):33985-33992. doi:10.48084/etasr.16707

BibTeX
@article{Thongkaew2026,
  author = {Thongkaew, Kunlapat and Ratanawilai, Thanate and Peter, Luksika and Mustafa, Zaleha},
  title = {An Assessment of Single- and Three-Layer Wood-Plastic Composite Hole-Machining Using Abrasive Waterjet Cutting},
  journal = {Engineering, Technology & Applied Science Research},
  year = {2026},
  volume = {16},
  number = {2},
  pages = {33985--33992},
  doi = {10.48084/etasr.16707}
}
Kostenlos starten →