EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Modeling Validation of Received Signal Strength Indicator (RSSI) Measurements Using ESP8266

Erwinsyah Sipahutar, Oktrison Oktrison, Alfi Hafizh, Rudi Arif Candra, Arie Budiansyah

International Journal of Multidisciplinary Sciences and Arts · 28.02.2026 · 5 (2) · 333-342

DOI: 10.47709/ijmdsa.v5i2.8076 ↗

Kurz gefasst

Fachartikel in der Zeitschrift International Journal of Multidisciplinary Sciences and Arts, online erschienen am 28.02.2026. Verfasst von Erwinsyah Sipahutar und 4 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The rapid proliferation of indoor Internet of Things (IoT) systems has intensified the need for cost-effective and energy-efficient wireless coverage extension solutions. Conventional commercial WiFi repeaters are often over-provisioned in terms of hardware capability and power consumption, making them unsuitable for small-scale IoT laboratories and energy-constrained environments. Although microcontroller-based platforms such as the ESP32 have been widely used for IoT gateways, their systematic evaluation as Network Address Translation (NAT)-based WiFi repeaters remains limited. This paper presents the design, implementation, and experimental performance evaluation of a low-cost ESP32-based NAT WiFi repeater for indoor IoT networks. The proposed architecture operates in dual-mode (Station + Access Point) configuration using a single 2.4 GHz radio interface and software-based NAT forwarding. Hardware optimization, including Bluetooth deactivation and transmission power tuning, is applied to reduce energy overhead. Experimental measurements conducted in an indoor laboratory environment evaluate throughput, latency, received signal strength indicator (RSSI), and power consumption. Results indicate that the proposed system achieves 15–35 Mbps throughput under single-client conditions, with an average latency increase of 3–8 ms compared to direct router connections. The repeater improves signal strength by up to 18 dB in weak-coverage areas, extending effective indoor coverage by approximately 10–20 m. Measured power consumption remains below 1.2 W during active forwarding, significantly lower than typical commercial repeaters. The main contribution of this work lies in providing a quantified energy–performance characterization of a microcontroller-based NAT repeater.

Zitieren

APA

Sipahutar, E., Oktrison, O., Hafizh, A., Candra, R. A., & Budiansyah, A. (2026). Modeling Validation of Received Signal Strength Indicator (RSSI) Measurements Using ESP8266. International Journal of Multidisciplinary Sciences and Arts, 5(2), 333-342. https://doi.org/10.47709/ijmdsa.v5i2.8076

Vancouver

Sipahutar E, Oktrison O, Hafizh A, Candra RA, Budiansyah A. Modeling Validation of Received Signal Strength Indicator (RSSI) Measurements Using ESP8266. International Journal of Multidisciplinary Sciences and Arts. 2026;5(2):333-342. doi:10.47709/ijmdsa.v5i2.8076

BibTeX
@article{Sipahutar2026,
  author = {Sipahutar, Erwinsyah and Oktrison, Oktrison and Hafizh, Alfi and Candra, Rudi Arif and Budiansyah, Arie},
  title = {Modeling Validation of Received Signal Strength Indicator (RSSI) Measurements Using ESP8266},
  journal = {International Journal of Multidisciplinary Sciences and Arts},
  year = {2026},
  volume = {5},
  number = {2},
  pages = {333--342},
  doi = {10.47709/ijmdsa.v5i2.8076}
}
Kostenlos starten →