EUVIMEDEUVIMED entdecken
Open Access · CC BY 4.0

Karakteristik Marshall pada Campuran CPHMA Menggunakan Filler Serbuk Keramik

Tio Firman Syah, Nurani Hartatik, Dika Ayu Safitri, Eko Andrianto

Jurnal Sains dan Teknologi (JSIT) · 03.06.2026 · 6 (2) · 421-431

DOI: 10.47233/jsit.v6i2.4736 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Jurnal Sains dan Teknologi (JSIT), online erschienen am 03.06.2026. Verfasst von Tio Firman Syah und 3 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The increasing development of road infrastructure in Indonesia has led to a significant rise in the demand for asphalt pavement materials every year. The continuous use of conventional materials, especially aggregates and limestone filler, causes environmental impacts such as land degradation, increased carbon emissions, and the accumulation of non-biodegradable construction waste. One potential waste material that can be utilized is ceramic powder waste, which has physical and chemical characteristics similar to conventional fillers. However, studies regarding the utilization of ceramic powder waste as a filler in Cold Paving Hot Mix Asbuton (CPHMA) mixtures are still limited. This study aims to analyze the Marshall characteristics of Cold Paving Hot Mix Asbuton (CPHMA) mixtures using ceramic powder waste as a filler substitution and to evaluate their compliance with the 2018 General Specifications of Bina Marga. The research was conducted experimentally through laboratory testing of aggregate characteristics, B50/30 asphalt, and ceramic powder waste filler. Furthermore, CPHMA specimens were prepared using filler variations of 1%, 1.5%, and 2%, followed by Marshall testing to analyze stability, flow, Voids in Mix (VIM), Voids in Mineral Aggregate (VMA), Voids Filled with Bitumen (VFB), Marshall Quotient (MQ), and Residual Marshall Stability (RMS). The test results were analyzed and compared with the requirements of the 2018 General Specifications of Bina Marga. The results showed that ceramic powder waste has the potential to be used as an alternative filler in CPHMA cold asphalt mixtures. All filler variations satisfied the Marshall requirements based on the 2018 General Specifications of Bina Marga. The 1.5% filler variation produced the most optimal mixture characteristics with a stability value of 510 kg, flow of 5.1 mm, VIM of 8.9%, VMA of 24.5%, VFB of 63.9%, and Residual Marshall Stability of 128%. The utilization of ceramic powder waste also has the potential to support sustainable development through the use of non-biodegradable waste as a more environmentally friendly road pavement material.

Zitieren

APA

Syah, T. F., Hartatik, N., Safitri, D. A., & Andrianto, E. (2026). Karakteristik Marshall pada Campuran CPHMA Menggunakan Filler Serbuk Keramik. Jurnal Sains dan Teknologi (JSIT), 6(2), 421-431. https://doi.org/10.47233/jsit.v6i2.4736

Vancouver

Syah TF, Hartatik N, Safitri DA, Andrianto E. Karakteristik Marshall pada Campuran CPHMA Menggunakan Filler Serbuk Keramik. Jurnal Sains dan Teknologi (JSIT). 2026;6(2):421-431. doi:10.47233/jsit.v6i2.4736

BibTeX
@article{Syah2026,
  author = {Syah, Tio Firman and Hartatik, Nurani and Safitri, Dika Ayu and Andrianto, Eko},
  title = {Karakteristik Marshall pada Campuran CPHMA Menggunakan Filler Serbuk Keramik},
  journal = {Jurnal Sains dan Teknologi (JSIT)},
  year = {2026},
  volume = {6},
  number = {2},
  pages = {421--431},
  doi = {10.47233/jsit.v6i2.4736}
}
Kostenlos starten →