Mechanical, Chemical, And Morphological Characterization Of 1% Nanofiber-Reinforced Self-Cure Acrylic For Denture Applications
Interdental Jurnal Kedokteran Gigi (IJKG) · 12.08.2026 · 22 (2) · 275-283
DOI: 10.46862/interdental.v22i2.14342 ↗Kurz gefasst
Fachartikel in der Zeitschrift Interdental Jurnal Kedokteran Gigi (IJKG), online erschienen am 12.08.2026. Verfasst von Ira Artilia und 7 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-SA 4.0).
Abstract (Originalsprache)
Introduction
Self-curing resin acrylic (SC-AR) is widely used for biomedical appliances, particularly prostheses, due to its rapid manipulation and suitability for single-visit fabrication. However, its relatively low mechanical strength may increase fracture susceptibility. This study evaluated the effect of incorporating 1 wt% polyacrylonitrile polymethyl methacrylate electrospinning nanofibers (e-nanoPAN-PMMA) on the physicochemical, mechanical, and morphological characteristics of SC-AR. Materials and Methods: SC-AR specimens were divided into conventional SC-AR (SC-ARc) and nano-reinforced SC-AR (SC-ARnano) groups. Chemical characteristics were evaluated using X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). Flexural strength (FS) and flexural modulus (FM) were assessed using a three-point bending test, while fracture-surface morphology was examined using scanning electron microscopy (SEM). Data were analyzed using an independent t-test (P≤0.05). Results and Discussion: SC-ARnano exhibited significantly higher FS and FM than SC-ARc (P≤0.05). XRD patterns showed characteristic polymeric resin features in both groups, with no additional crystalline peaks in SC-ARnano. FTIR revealed a nitrile absorption band in SC-ARnano. SEM demonstrated nanofibers embedded within the resin matrix, with no detectable surface porosity.
Conclusion
Incorporation of 1 wt% e-nanoPAN-PMMA significantly improved the mechanical properties of SC-AR while maintaining its physicochemical characteristics. SC-ARnano demonstrates potential as a reinforced acrylic resin for biomedical applications.
Zitieren
APA
Artilia, I., Syahira, G. A., Dewi, Z. Y., Rahaju, A., Dewi, R. S., Nuraeni, N., Handayani, N., & Sidiqa, A. N. (2026). Mechanical, Chemical, And Morphological Characterization Of 1% Nanofiber-Reinforced Self-Cure Acrylic For Denture Applications. Interdental Jurnal Kedokteran Gigi (IJKG), 22(2), 275-283. https://doi.org/10.46862/interdental.v22i2.14342
Vancouver
Artilia I, Syahira GA, Dewi ZY, Rahaju A, Dewi RS, Nuraeni N, et al. Mechanical, Chemical, And Morphological Characterization Of 1% Nanofiber-Reinforced Self-Cure Acrylic For Denture Applications. Interdental Jurnal Kedokteran Gigi (IJKG). 2026;22(2):275-283. doi:10.46862/interdental.v22i2.14342
BibTeX
@article{Artilia2026,
author = {Artilia, Ira and Syahira, Gina Adry and Dewi, Zwista Yulia and Rahaju, Asih and Dewi, Rheni Safira and Nuraeni, Nunung and Handayani, Nurrahmi and Sidiqa, Atia Nurul},
title = {Mechanical, Chemical, And Morphological Characterization Of 1% Nanofiber-Reinforced Self-Cure Acrylic For Denture Applications},
journal = {Interdental Jurnal Kedokteran Gigi (IJKG)},
year = {2026},
volume = {22},
number = {2},
pages = {275--283},
doi = {10.46862/interdental.v22i2.14342}
}
EUVIMED