EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Effects of Firing Temperature on the Compressive Strength of a Clay Burnt Bricks Produced in Benue State

Ishaku Habu, Erasoo E. Varvar

Scholarly Journal of Science and Technology Research and Development · 25.04.2026 · 5 (2) · 12-30

DOI: 10.46654/yz8tvp72 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Scholarly Journal of Science and Technology Research and Development, online erschienen am 25.04.2026. Verfasst von Ishaku Habu und 1 weiteren Autor:innen. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Clay bricks remain the most widely used conventional construction materials in the building and construction industries worldwide, due to their good qualities, affordability and versatility compared to other materials for building purposes. This work involved onsite observation and laboratory test of the production process of Benue clay burnt bricks (BCBB) to determine the effects of firing temperature on compressive strength, water absorption and saturation coefficient of BCBB. Experimental research was used in carrying out the work through laboratory test and visit to observe and study the firing temperature management practices of some traditional brick production in Benue State. A total of 36 brick specimens, of the BCBB was examined in the laboratory for compressive strength, water absorption and saturation coefficient using a temperature range of 900°c, 1000°c and 1200°c. The observation shows that the traditional brick factories surveyed during this study have no temperature device for their kiln but it is done with the observation of their kiln operators. Major problem in traditional bricks factories in the study area is the usual loss of over and under fired clay-bricks. The Atterberg’s limit test results reveal that soil sample from Kpege burnt bricks production site has a liquid limit of 40.6, plastic limit of 23.4, plastic index of 17.2 and linear shrinkage of 7.3 while Ichwa burnt bricks production site has a liquid limit of 56.2, plastic limit of 27.6, plastic index of 28.8 and linear shrinkage of 7.4. The average compressive strength was 23.10 N/mm2 and 22.60 N/mm2 for Samples from Kpege and Ichwa respectively; Average water absorption for Sample from Ichwa soil sample is 9.62% which is almost 3% higher than that of Kpege soil sample which is 6.36% while the saturation coefficient of Ichwa soil sample is 0.78 which is 0.10 higher than Kpege soil sample with 0.66. This indicate that with increment of duration from 6,7, and 8hrs of firing slightly increases the compressive strength and lowers both the water absorption and saturation coefficient. It was concluded that the allowable mechanical property for brick samples within the temperature range considered is obtained at 1000°c to 1200°c and firing duration of 7hrs to 8hrs produce a high quality burnt bricks that can serve all purpose in building production.

Zitieren

APA

Habu, I., & Varvar, E. E. (2026). Effects of Firing Temperature on the Compressive Strength of a Clay Burnt Bricks Produced in Benue State. Scholarly Journal of Science and Technology Research and Development, 5(2), 12-30. https://doi.org/10.46654/yz8tvp72

Vancouver

Habu I, Varvar EE. Effects of Firing Temperature on the Compressive Strength of a Clay Burnt Bricks Produced in Benue State. Scholarly Journal of Science and Technology Research and Development. 2026;5(2):12-30. doi:10.46654/yz8tvp72

BibTeX
@article{Habu2026,
  author = {Habu, Ishaku and Varvar, Erasoo E.},
  title = {Effects of Firing Temperature on the Compressive Strength of a Clay Burnt Bricks Produced in Benue State},
  journal = {Scholarly Journal of Science and Technology Research and Development},
  year = {2026},
  volume = {5},
  number = {2},
  pages = {12--30},
  doi = {10.46654/yz8tvp72}
}
Kostenlos starten →