EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC 4.0

Effect of Hot Isostatic Pressing on the Stellite 6 Alloy prepared by Directed Energy Deposition

Joowon Suh, Jae Hyeon Koh, Young-Bum Chun, Young Do Kim, Jinsung Jang, Suk Hoon Kang, Heung Nam Han

journal of Korean Powder Metallurgy Institute · 2024

DOI: 10.4150/jpm.2024.00066 ↗

Kurz gefasst

Fachartikel in der Zeitschrift journal of Korean Powder Metallurgy Institute, 2024. Verfasst von Joowon Suh und 6 weiteren Autor:innen. Die Arbeit wurde bisher 1-mal zitiert (Crossref) und nennt 36 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC 4.0). Gefördert von: Korea Atomic Energy Research Institute.

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

The directed energy deposited (DED) alloys show higher hardness values than the welded alloys due to the finer microstructure following the high cooling rate. However, defects such as microcracks, pores, and the residual stress are remained within the DED alloy. These defects deteriorate the wear behavior so post-processing such as heat treatment and hot isostatic pressing (HIP) are applied to DED alloys to reduce the defects. HIP was chosen in this study because the high pressure and temperature uniformly reduced the defects. The HIP is processed at 1150oC under 100 MPa for 4 hours. After HIP, microcracks are disappeared and porosity is reduced by 86.9%. Carbides are spherodized due to the interdiffusion of Cr and C between the dendrite and interdendrite region. After HIP, the nanohardness (GPa) of carbides increased from 11.1 to 12, and the Co matrix decreased from 8.8 to 7.9. Vickers hardness (HV) decreased by 18.9 % after HIP. The dislocation density (10-2/m2) decreased from 7.34 to 0.34 and the residual stress (MPa) changed from tensile 79 to a compressive -246 by HIP. This study indicates that HIP is effective in reducing defects, and the HIP DED Stellite 6 exhibits a higher HV than welded Stellite 6.

Förderung

  • Korea Atomic Energy Research Institute

Zitieren

APA

Suh, J., Koh, J. H., Chun, Y., Kim, Y. D., Jang, J., Kang, S. H., & Han, H. N. (2024). Effect of Hot Isostatic Pressing on the Stellite 6 Alloy prepared by Directed Energy Deposition. journal of Korean Powder Metallurgy Institute. https://doi.org/10.4150/jpm.2024.00066

Vancouver

Suh J, Koh JH, Chun Y, Kim YD, Jang J, Kang SH, et al. Effect of Hot Isostatic Pressing on the Stellite 6 Alloy prepared by Directed Energy Deposition. journal of Korean Powder Metallurgy Institute. 2024. doi:10.4150/jpm.2024.00066

BibTeX
@article{Suh2024,
  author = {Suh, Joowon and Koh, Jae Hyeon and Chun, Young-Bum and Kim, Young Do and Jang, Jinsung and Kang, Suk Hoon and Han, Heung Nam},
  title = {Effect of Hot Isostatic Pressing on the Stellite 6 Alloy prepared by Directed Energy Deposition},
  journal = {journal of Korean Powder Metallurgy Institute},
  year = {2024},
  doi = {10.4150/jpm.2024.00066}
}
Kostenlos starten →