EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Stress distribution in miniscrews with different insertion angles: A finite element analysis study

Rishibha Bhardwaj, Dhara Shukla, P C Ramesh Kumar, Rohit Bahri, Naveen R Reddy, Snigdha Pattanaik, Azhar Mohammed, A N Prakruti

Journal of Orthodontic Science · 2026-05 · 15 (1)

DOI: 10.4103/jos.jos_200_25 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Orthodontic Science, 2026-05. Verfasst von Rishibha Bhardwaj und 7 weiteren Autor:innen. Beteiligte Einrichtung: Associate Professor, Department of Orthodontics, School of Dental Sciences, Sharda University, Greater Noida, India. Die Arbeit nennt 29 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

BACKGROUND/OBJECTIVES: Orthodontic miniscrews serve as critical temporary anchorage devices (TADs), but their clinical success is often limited by biomechanical instability. This research was done to evaluate the biomechanical impact of different miniscrew insertion angles on stress distribution and micromotion using finite element analysis (FEA). METHODOLOGY: FEA was performed on a total of 225 mandibular models derived from cone beam computed tomography scans of Indian adults. Titanium alloy (Ti-6Al-4V) miniscrews with Sandblasted, Large-grit, Acidsurface modification was inserted at angles of 30°, 45°, 60°, and 90°. Each setup was subjected to vertical and oblique orthodontic loads of 2 N and 5 N. Stress, displacement, and micromotion were analyzed, and the obtained data were statistically evaluated. RESULTS: Miniscrew insertion at 45° demonstrated the most favorable biomechanical profile, with the lowest von Mises stress (61.2 MPa), minimal micromotion (0.033 mm), and optimal stress distribution. Insertion angle had a significant effect on stress ( P < 0.001), and regression analysis identified insertion angle and bone density as significant predictors of stress and micromotion (adjusted R ² = 0.89). The odds of failure due to high stress and micromotion were highest at insertion angles of 90° and 30°, respectively.Multivariate regression revealed that both insertion angle and bone density significantly influenced miniscrew stress and micromotion, with optimal 45° angulation and higher bone density minimizing failure risk (adjusted R ² = 0.89). CONCLUSION: A 45° insertion angle offers biomechanical superiority for miniscrew placement, reducing stress concentrations and the risk of micromotion. These findings provide evidence-based guidance for clinical orthodontic practice, particularly in Indian populations.

Schlagwörter

Stichwörter der Autor:innen

Bone densityfinite element analysisinsertion anglemicromotionminiscreworthodontic anchoragestress distribution

Autor:innen und Institutionen

  • Associate Professor, Department of Orthodontics, School of Dental Sciences, Sharda University, Greater Noida, India.
  • Assistant Professor, Department of Dentistry, GMERS Medical College and Hospital, Gotri, Vadodara, Gujarat, India.
  • Professor and HOD, Department of Orthodontics and Dentofacial Orthopedics, HKDET Dental College, Humnabad, Karnataka, India.
  • Professor, Department of Orthodontics and Dentofacial Orthopedics, Azamgarh Dental College, Azamgarh, Uttar Pradesh, India.
  • Department of Prosthodontics, College of Dentistry, Jazan University, Saudi Arabia.
  • Assistant Professor, Department of Orthodontics, Pediatric and Community Dentistry, University of Sharjah, UAE.

Zitieren

APA

Bhardwaj, R., Shukla, D., Kumar, P. C. R., Bahri, R., Reddy, N. R., Pattanaik, S., Mohammed, A., & Prakruti, A. N. (2026). Stress distribution in miniscrews with different insertion angles: A finite element analysis study. Journal of Orthodontic Science, 15(1). https://doi.org/10.4103/jos.jos_200_25

Vancouver

Bhardwaj R, Shukla D, Kumar PCR, Bahri R, Reddy NR, Pattanaik S, et al. Stress distribution in miniscrews with different insertion angles: A finite element analysis study. Journal of Orthodontic Science. 2026;15(1). doi:10.4103/jos.jos_200_25

BibTeX
@article{Bhardwaj2026,
  author = {Bhardwaj, Rishibha and Shukla, Dhara and Kumar, P C Ramesh and Bahri, Rohit and Reddy, Naveen R and Pattanaik, Snigdha and Mohammed, Azhar and Prakruti, A N},
  title = {Stress distribution in miniscrews with different insertion angles: A finite element analysis study},
  journal = {Journal of Orthodontic Science},
  year = {2026},
  volume = {15},
  number = {1},
  doi = {10.4103/jos.jos_200_25}
}
Kostenlos starten →