EUVIMEDEUVIMED entdecken
VergleichsstudieOpen Access · CC BY-NC-ND 4.0

Influence of intraoral and laboratory scanning systems on the marginal fit of direct metal laser-sintered copings: An in vitro study

P S Prakhyath, Bharath Prabhu, Shijal Narayan Suvarna

The Journal of Indian Prosthodontic Society · 2026

DOI: 10.4103/jips.jips_13_26 ↗

Kurz gefasst

Vergleichsstudie in der Zeitschrift The Journal of Indian Prosthodontic Society, 2026. Verfasst von P S Prakhyath und 2 weiteren Autor:innen. Beteiligte Einrichtung: Department of Prosthodontics and Implantology, A J Institute of Dental Sciences, Mangaluru, Karnataka, India. Hauptthemen laut MEDLINE: Computer-Aided Design, Dental Marginal Adaptation, Lasers, Crowns. Die Arbeit nennt 25 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractSchlagwörterBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

Aim

This study aimed to evaluate and compare the vertical marginal discrepancy of DMLS copings fabricated from stone dies scanned using an intraoral scanner (IOS) and a laboratory scanner. Settings and Design: An in vitro comparative study was conducted to evaluate the influence of intraoral and laboratory scanning systems on the vertical marginal discrepancy of DMLS copings. Materials and Methods: A customised stainless-steel model simulating a prepared tooth with a shoulder finish line was fabricated. Impressions of the model were made using elastomeric impression material. Forty dies ( n =40) were poured using type IV dental stone and divided into two groups ( n =20). Group 1 dies were scanned using a 3Shape TRIOS IOS and Group 2 dies were scanned using a 3Shape extraoral laboratory scanner. Copings were fabricated using CAD/CAM software. Marginal gap between the die and the coping was measured at 4 predetermined points (buccal, lingual, mesial, and distal) using a stereomicroscope at ×40 magnification. Statistical Analysis Used: Data were analysed using SPSS (version 21, IBM Corp., Armonk, NY, USA). Student’s unpaired t-test was used to compare the tested groups. The collected data were analysed at a significance level set at P < 0.05.

Results

The mean marginal gap between the die and coping was 11.44 μm for Group 1 and 29.62 μm for Group 2. The difference between the groups was statistically significant ( P < 0.001).

Conclusion

Copings fabricated from dies scanned using IOS demonstrated significantly lower vertical marginal discrepancies compared to those scanned using the laboratory scanner. However, the marginal gaps observed in both groups were within clinically acceptable limits.

Schlagwörter

MeSH-Schlagwörter (MEDLINE)

Computer-Aided DesignDental Marginal AdaptationLasersCrownsDental Prosthesis DesignIn Vitro TechniquesHumansModels, DentalStainless Steel

Stichwörter der Autor:innen

Direct metal laser sintered copingsintraoral scannerlaboratory scannermarginal fitstereomicroscope

Substanzen

Stainless Steel

Autor:innen und Institutionen

  • Department of Prosthodontics and Implantology, A J Institute of Dental Sciences, Mangaluru, Karnataka, India.
  • Department of Prosthodontics and Implantology, Srinivas Institute of Dental Sciences, Mangaluru, Karnataka, India.

Zitieren

APA

Prakhyath, P. S., Prabhu, B., & Suvarna, S. N. (2026). Influence of intraoral and laboratory scanning systems on the marginal fit of direct metal laser-sintered copings: An in vitro study. The Journal of Indian Prosthodontic Society. https://doi.org/10.4103/jips.jips_13_26

Vancouver

Prakhyath PS, Prabhu B, Suvarna SN. Influence of intraoral and laboratory scanning systems on the marginal fit of direct metal laser-sintered copings: An in vitro study. The Journal of Indian Prosthodontic Society. 2026. doi:10.4103/jips.jips_13_26

BibTeX
@article{Prakhyath2026,
  author = {Prakhyath, P S and Prabhu, Bharath and Suvarna, Shijal Narayan},
  title = {Influence of intraoral and laboratory scanning systems on the marginal fit of direct metal laser-sintered copings: An in vitro study},
  journal = {The Journal of Indian Prosthodontic Society},
  year = {2026},
  doi = {10.4103/jips.jips_13_26}
}
Kostenlos starten →