Surface topographical changes of restorative composite materials in distilled and fluoride-contaminated water: An atomic force microscopy study
Journal of Conservative Dentistry and Endodontics · 2026-11 · 29 (11) · 1284-1292
DOI: 10.4103/jcde.jcde_515_26 ↗Kurz gefasst
Fachartikel in der Zeitschrift Journal of Conservative Dentistry and Endodontics, online erschienen am 05.10.2026. Verfasst von Priyabrata Mandal und 2 weiteren Autor:innen. Die Arbeit nennt 33 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).
Abstract (Originalsprache)
Aim
The aim of the study was to compare surface topographical changes of two restorative composites after immersion in distilled water and fluoride-contaminated water using Atomic Force Microscopy (AFM). Materials and Methods: Sixty disc specimens (8 mm × 2 mm) were prepared from a fluoride-releasing Giomer (Beautifil II) and a nonfluoride-releasing (Ivoclar) composite resin using a polylactic acid mold. Specimens were allocated to four groups by material and immersion medium (distilled water or fluoride-contaminated water). After light polymerization per manufacturer’s instructions, all samples were stored at 37°C for 28 days. Surface roughness was measured by AFM before and after immersion, and three-dimensional (3D) topographical images were analyzed. Roughness parameters average roughness (Ra) and root mean square roughness (Rq) were compared using one-way analysis of variance with significance set at P < 0.05.
Results
AFM 3D analyses revealed material- and medium-dependent alterations in surface morphology. The fluoride-releasing composite immersed in distilled water exhibited comparatively smoother surfaces, whereas immersion in fluoride-contaminated water produced pronounced irregularities and peak formations in both materials. Fluoride contamination increased surface roughness across groups. For Giomer, Ra rose from 8.58 ± 1.29 to 15.86 ± 4.58 µm ( P = 0.046) and Rq from 15.48 ± 2.08 to 18.92 ± 4.64 µm ( P = 0.245). For the Ivoclar composite, Ra increased from 9.33 ± 1.71 to 13.66 ± 3.33 µm ( P = 0.049) and Rq from 14.48 ± 1.29 to 18.17 ± 4.90 µm ( P = 0.237). Thus, Ra changes were statistically significant for both materials, while Rq changes were not.
Conclusion
Fluoride contaminated water promotes surface degradation in both restorative composites, increasing roughness and topographical irregularities. The non–fluoride releasing composite demonstrated comparatively greater degradation than the Giomer. These findings underscore the influence of environmental fluoride on composite surface integrity and may inform material selection and maintenance protocols.
Zitieren
APA
Mandal, P., Laha, A., & Roy, P. K. (2026). Surface topographical changes of restorative composite materials in distilled and fluoride-contaminated water: An atomic force microscopy study. Journal of Conservative Dentistry and Endodontics, 29(11), 1284-1292. https://doi.org/10.4103/jcde.jcde_515_26
Vancouver
Mandal P, Laha A, Roy PK. Surface topographical changes of restorative composite materials in distilled and fluoride-contaminated water: An atomic force microscopy study. Journal of Conservative Dentistry and Endodontics. 2026;29(11):1284-1292. doi:10.4103/jcde.jcde_515_26
BibTeX
@article{Mandal2026,
author = {Mandal, Priyabrata and Laha, Abhishek and Roy, Pankaj Kumar},
title = {Surface topographical changes of restorative composite materials in distilled and fluoride-contaminated water: An atomic force microscopy study},
journal = {Journal of Conservative Dentistry and Endodontics},
year = {2026},
volume = {29},
number = {11},
pages = {1284--1292},
doi = {10.4103/jcde.jcde_515_26}
}
EUVIMED