Multifunctional Silicone Hotmelt Materials Integrating Stress Relaxation and Thermal Management for Advanced Electronic
IMAPSource Proceedings · 27.10.2026 · 2026 (Symposium)
DOI: 10.4071/001c.173328 ↗Kurz gefasst
Fachartikel in der Zeitschrift IMAPSource Proceedings, online erschienen am 27.10.2026. Verfasst von Ryosuke Yamazaki und 5 weiteren Autor:innen.
Abstract (Originalsprache)
Advanced electronic packaging technologies, including wafer-level packaging (WLP) and panel-level packaging (PLP), increasingly require thinner and larger substrates to support high-throughput manufacturing. At the same time, flexible and foldable electronic devices are rapidly emerging, further increasing the demand for encapsulant and adhesive materials with both high mechanical compliance and effective thermal stress management. Conventional organic-based materials, such as epoxy, acrylic, and urethane resins, are often limited in these applications because their high elastic modulus, typically greater than 1 GPa, tends to generate excessive thermal stress and insufficient flexibility. Silicone materials are attractive candidates because of their inherently low elastic modulus and excellent thermal and chemical stability. However, their relatively high coefficient of thermal expansion (CTE) has generally limited their use in thin and large-area substrates unless extremely soft gel-type formulations are employed. In this work, a newly developed silicone hotmelt material is presented as a solution to this challenge. Owing to a unique silicone network design, the material provides effective thermal stress dissipation despite a relatively high CTE of approximately 220 ppm/K and an elastic modulus in the range of 10–100 MPa. This silicone hotmelt is available in both film form, referred to as Silicone Hotmelt Film (SHF), and cartridge form, referred to as Silicone Hotmelt Cartridge (SHC), with melt characteristics optimized for film lamination and hot-dispensing processes, respectively. Its rapid thermosetting behavior enables compatibility with high-throughput manufacturing processes for advanced electronic devices. When laminated and cured onto dummy substrates representative of WLP and PLP structures, no measurable warpage was observed, indicating excellent stress relaxation. In addition, reliability testing, including thermal cycling from −40 °C to 150 °C, showed no delamination or cracking in the laminated bodies, demonstrating robust durability under harsh conditions. The material also exhibits adhesion to a broad range of substrates, including cured silicone, fluoropolymers such as ethylene tetrafluoroethylene (ETFE), and precious metals such as gold. This feature enables structural bonding between dissimilar materials with mismatched CTE values. Reliability results obtained from multilayer structures composed of two different substrates and the silicone hotmelt further support its applicability to advanced packaging assemblies. Although silicone materials are generally known for thermal stability over a typical operating range of approximately −50 °C to 200 °C, the newly developed silicone hotmelt exhibited substantially enhanced performance, remaining stable over an extended temperature range from −100 °C to 300 °C. No embrittlement was observed below −50 °C, and strong adhesion was retained even after aging at 300 °C, demonstrating durability beyond that of conventional silicone materials. Furthermore, a thermally conductive version of the silicone hotmelt was developed by integrating thermal management technology into the same material architecture, achieving thermal conductivity of up to 3 W m⁻¹ K⁻¹ without substantial loss of mechanical compliance or adhesion. This combination of high thermal stability, stress relaxation, and thermal conductivity makes the material particularly suitable for advanced electronic packaging applications that require both long-term reliability and efficient heat dissipation. Overall, these results indicate that the developed silicone hotmelt materials provide a promising encapsulation and adhesive solution for advanced electronic packaging applications requiring effective thermal stress management, high reliability, and, in some cases, enhanced thermal conductivity, particularly for thin, large-area, and flexible electronic devices.
Zitieren
APA
Yamazaki, R., Chen, H. C., Sootsman, J. R., Yang, X., Akiyama, K., & Ko, E. (2026). Multifunctional Silicone Hotmelt Materials Integrating Stress Relaxation and Thermal Management for Advanced Electronic. IMAPSource Proceedings, 2026(Symposium). https://doi.org/10.4071/001c.173328
Vancouver
Yamazaki R, Chen HC, Sootsman JR, Yang X, Akiyama K, Ko E. Multifunctional Silicone Hotmelt Materials Integrating Stress Relaxation and Thermal Management for Advanced Electronic. IMAPSource Proceedings. 2026;2026(Symposium). doi:10.4071/001c.173328
BibTeX
@article{Yamazaki2026,
author = {Yamazaki, Ryosuke and Chen, Hsiang Chuan and Sootsman, Joseph R. and Yang, Xi and Akiyama, Katsuhiro and Ko, Eun},
title = {Multifunctional Silicone Hotmelt Materials Integrating Stress Relaxation and Thermal Management for Advanced Electronic},
journal = {IMAPSource Proceedings},
year = {2026},
volume = {2026},
number = {Symposium},
doi = {10.4071/001c.173328}
}
EUVIMED