EUVIMEDEUVIMED entdecken
Open Access · CC BY-NC-ND 4.0

Copper to Copper TCB – A Key Enabler for Ultra-Fine Pitch Heterogeneous Applications

Suleman Ayub, Adeel Bajwa, Ryo Sugano, Tetsuya Ogawa, Tom Colosimo, Bob Chylak

Journal of Microelectronics and Electronic Packaging · 2025

DOI: 10.4071/001c.140810 ↗

Kurz gefasst

Fachartikel in der Zeitschrift Journal of Microelectronics and Electronic Packaging, 2025. Verfasst von Suleman Ayub und 5 weiteren Autor:innen. Die Arbeit wurde bisher 3-mal zitiert (Crossref) und nennt 10 Literaturangaben. Der Volltext ist frei zugänglich (Open Access, CC BY-NC-ND 4.0).

AbstractBibliografische AngabenZitierenVerwandte Studien

Abstract (Originalsprache)

In this paper, we demonstrate the direct Cu-Cu thermal compression bonding (TCB) for fine-pitch heterogeneous integration by leveraging a pre-applied underfill making it comparable to the traditional solder-based TCB using non-conductive films (NCF). In contrast to the well-known inorganic dielectric hybrid bonding process for fine-pitch interconnects where the dielectric like SiO 2 is bonded first, followed by Cu bonding in a batch-anneal process, our approach sets forth a single-step process for attaching both the dielectric and Cu pillars. The high costs associated with hybrid bonding process due to its stringent cleanroom requirements, material handling and pre-/post-processing is currently limiting its industry-wide adoption, whereas the use of inorganic dielectric in this case relieves many of the stringent process and infrastructure requirements. The Cu-Cu TCB demonstrated in this paper is carried out in a state-of-the-art high-accuracy TCB tool developed by Kulicke and Soffa Industries (K&S) capable of rapidly heating/cooling the source die, perform in-situ flux-less reduction of Cu oxide using vaporized formic acid, and applying high pressures up to an equivalent of 500 N during bonding. The test vehicles incorporate dielectric material researched by Resonac Inc., which is an organic layer spin-coated and partially cured onto a wafer terminated with Cu pillars followed by a tailored chemical-mechanical polishing process (CMP). The adhesion strength of the bonded dielectric has been experimentally determined at approx. 21 MPa for a 4×4 mm 2 die. For Cu-Cu TCB, the 5.1×5.1 mm 2 source dies consisting of 10-µm-diameter Cu pillars equally spaced at a 20 µm pitch are bonded to target sites on coupons measuring 10.2×15.3 mm 2 . The Cu-Cu TVs bonded and annealed for over 8 hrs at 250°C showed noticeable grain-growth across the interface. As our approach eliminates the requirement of a post-bond underfill, it is a viable solution for scaling heterogeneous integration down to sub-5 µm pitch interconnects.

Zitieren

APA

Ayub, S., Bajwa, A., Sugano, R., Ogawa, T., Colosimo, T., & Chylak, B. (2025). Copper to Copper TCB – A Key Enabler for Ultra-Fine Pitch Heterogeneous Applications. Journal of Microelectronics and Electronic Packaging. https://doi.org/10.4071/001c.140810

Vancouver

Ayub S, Bajwa A, Sugano R, Ogawa T, Colosimo T, Chylak B. Copper to Copper TCB – A Key Enabler for Ultra-Fine Pitch Heterogeneous Applications. Journal of Microelectronics and Electronic Packaging. 2025. doi:10.4071/001c.140810

BibTeX
@article{Ayub2025,
  author = {Ayub, Suleman and Bajwa, Adeel and Sugano, Ryo and Ogawa, Tetsuya and Colosimo, Tom and Chylak, Bob},
  title = {Copper to Copper TCB – A Key Enabler for Ultra-Fine Pitch Heterogeneous Applications},
  journal = {Journal of Microelectronics and Electronic Packaging},
  year = {2025},
  doi = {10.4071/001c.140810}
}
Kostenlos starten →